ssr reverse mesh

[ef-civic]

hey is there such thing as 4 x 100 reverse mesh rims ?

[STTICH]

yes of course.

hard to come by tho.

[Sir_vtec]

yes. hard to find. expect to pay more.

[ef-civic]

so it would be cheaper to buy 4 x 114 brake setup and then buy some ??

[Sir_vtec]

4x114.3 for reverse mesh doesnt cost much. maybe 500 for a set of 15", sometimes cheaper cos its common in japan. If u can source cheap 4x114.3 brake kit then go for it, 4x114.3 wheels are cheap compared to 4x100.

[ef-civic]

dang it lol if i was to find a set of 4 x 100 ones. where would i have to look ? lol cause arent the going rate for 4 x 114 like 800 ?

[LowEk]

so it would be cheaper to buy 4 x 114 brake setup and then buy some ??


If you ask me just save the money you are going to spend in the brake change just so u can save money and spend it on the 4x100 as you said they will cost abit more.

[SHOGUNOVDDRK]

IMO Do the Brake Upgrade anyway and buy some SSR's in that stud Pattern and make it easy on yourself :p

In reality it depends on how long you are willing to wait for for 4x100 Reverse Meshies and how loose your purse strings are.

[ef-civic]

hmm i really want em but i dont wanna go through all the trouble of changing brakes.. anything else close to them ?

[trism]

just remember that if yu change your brakes just for the SSRs, then all your 4x100 wheels are fuxxored


just buy hubcentric spacers that chaNGE THE STUD PATTERN

[Lukey]

just remember that if yu change your brakes just for the SSRs, then all your 4x100 wheels are fuxxored


just buy hubcentric spacers that chaNGE THE STUD PATTERN

would you need extended studs because ur running a spacer?

[ef-civic]

just remember that if yu change your brakes just for the SSRs, then all your 4x100 wheels are fuxxored


just buy hubcentric spacers that chaNGE THE STUD PATTERN

where do u get this from ????? :eek:

[I heart the SSS]

would you need extended studs because ur running a spacer?

No you nub ,these are HUBCENTRIC spacers meaning they BOLT ON to your exsisting studs and give you NEW STUDS to mount the wheel too.

Not slip on spacers, which you are thinking of.

Yiu can get spacers that bolt onto a 4x100 and give you a 4x114 or even 4x100 to 5x114.

[Chernoby1]

No you nub ,these are HUBCENTRIC spacers meaning they BOLT ON to your exsisting studs and give you NEW STUDS to mount the wheel too.

Not slip on spacers, which you are thinking of.

Yiu can get spacers that bolt onto a 4x100 and give you a 4x114 or even 4x100 to 5x114.

Preety sure there are legality problems with this im most states

[ef-civic]

lol so where ya get it from ?

[SHOGUNOVDDRK]

Preety sure there are legality problems with this im most states


lol so where ya get it from ?

See Cherboby, he wants the mod bad enough.

[ef-civic]

can u get them in aus ??

[Sir_vtec]

Lukey

Any spacers under 5mm is ok to slip on without extended studs, but its best u get extended studs if u want to run spacers. Oem studs werent made to take the whole car load. Eclipsor has 5mm spacers on his cb accord. I have had non hub centric 5mm spacers on the rears no probs but i would never run non hub centric spacers at the front.

[chargeR]

just remember that if yu change your brakes just for the SSRs, then all your 4x100 wheels are fuxxored


just buy hubcentric spacers that chaNGE THE STUD PATTERN

This = less dish though. Since the wheels have to be significantly higher offset. Less dish makes charger sad, since it is the whole reason to buy SSR meshies.

[trism]

yes, that is very true

but just do it anyway and run low offset+big camber=epic win :p

[Dreams]

good luck.

[sdewyz]

Bumping this shit up, thought better to do than opening a new thread. I have a set if ssr reverse mesh. Can I reverse mount these?? I want more dish!! Any ideas??