beeza
02-11-2009, 05:31 PM
Disclaimer: The following is provided as a GUIDE ONLY, and neither myself nor Ozhonda take any responsibility for the outcomes of someone else doing the following. You follow these steps at your own risk!
Aim:
To Mount the GPS because mounting the GPS on ya front window is Dangerous!
Required:
A piece of paper and a pen
A Texta
Some Perspex
Drill and 2 or 3 small drill bits
4 screws
A File
Steps:
Since the GPS has a suction mount,we will need to use Perspex:
http://i99.photobucket.com/albums/l287/beeza2/100_1488.jpg
Find a suitable location to mount the GPS and make up a template from which you will use to trace and cut the perspex:
http://i99.photobucket.com/albums/l287/beeza2/100_1459.jpg
Make sure the GPS will fit on there:
http://i99.photobucket.com/albums/l287/beeza2/100_1431.jpg
Bunnings sell perspex for $30 a sheet (gotta buy the whole sheet).I used 3mm thick perspex.Trace and cut with a hacksaw:
http://i99.photobucket.com/albums/l287/beeza2/100_1471.jpg
Simply use a file to round the edges off and use a texta to mark the best spots for the screws:
http://i99.photobucket.com/albums/l287/beeza2/100_1461.jpg
Check it will fit again:
http://i99.photobucket.com/albums/l287/beeza2/100_1458.jpg
Drill em' out,use a small drill bit to start,to prevent the perspex from splitting,then finish up with a drill bit just a touch smaller than the screws so the screw just bite's and grabs the perspex a touch:
http://i99.photobucket.com/albums/l287/beeza2/100_1492.jpg
http://i99.photobucket.com/albums/l287/beeza2/100_1462.jpg
Next we're gonna drill into where wires maybe so remove the backup fuse.You can just disconnect the negative battery cable instead.Also make sure you turn the alarm off if you have one or it will start wailing!:
http://i99.photobucket.com/albums/l287/beeza2/100_1465.jpg
http://i99.photobucket.com/albums/l287/beeza2/100_1464.jpg
Use a small drill bit again and work up to one just a bit smaller then the screw:
http://i99.photobucket.com/albums/l287/beeza2/100_1466.jpg
Done!
http://i99.photobucket.com/albums/l287/beeza2/100_1468.jpg
http://i99.photobucket.com/albums/l287/beeza2/100_1495.jpg
Dont mind the door trims,just painting em':
http://i99.photobucket.com/albums/l287/beeza2/100_1494.jpg
http://i99.photobucket.com/albums/l287/beeza2/100_1493.jpg
Perfect.Removing CD's? No problem!
http://i99.photobucket.com/albums/l287/beeza2/100_1516.jpg
Make sure you Reset the ECU (http://www.ozhonda.com/forum/showthread.php?t=67113) afterwards if you removed the back up fuse or the negative cable on the battery.
Other comments:
atm I'm using the power cord that plugs into the cigarette lighter,it's messy and ugly.I will wire the power cord up to a power source and post the results.
I'm Lovin' it! hehehe
:honda:
Aim:
To Mount the GPS because mounting the GPS on ya front window is Dangerous!
Required:
A piece of paper and a pen
A Texta
Some Perspex
Drill and 2 or 3 small drill bits
4 screws
A File
Steps:
Since the GPS has a suction mount,we will need to use Perspex:
http://i99.photobucket.com/albums/l287/beeza2/100_1488.jpg
Find a suitable location to mount the GPS and make up a template from which you will use to trace and cut the perspex:
http://i99.photobucket.com/albums/l287/beeza2/100_1459.jpg
Make sure the GPS will fit on there:
http://i99.photobucket.com/albums/l287/beeza2/100_1431.jpg
Bunnings sell perspex for $30 a sheet (gotta buy the whole sheet).I used 3mm thick perspex.Trace and cut with a hacksaw:
http://i99.photobucket.com/albums/l287/beeza2/100_1471.jpg
Simply use a file to round the edges off and use a texta to mark the best spots for the screws:
http://i99.photobucket.com/albums/l287/beeza2/100_1461.jpg
Check it will fit again:
http://i99.photobucket.com/albums/l287/beeza2/100_1458.jpg
Drill em' out,use a small drill bit to start,to prevent the perspex from splitting,then finish up with a drill bit just a touch smaller than the screws so the screw just bite's and grabs the perspex a touch:
http://i99.photobucket.com/albums/l287/beeza2/100_1492.jpg
http://i99.photobucket.com/albums/l287/beeza2/100_1462.jpg
Next we're gonna drill into where wires maybe so remove the backup fuse.You can just disconnect the negative battery cable instead.Also make sure you turn the alarm off if you have one or it will start wailing!:
http://i99.photobucket.com/albums/l287/beeza2/100_1465.jpg
http://i99.photobucket.com/albums/l287/beeza2/100_1464.jpg
Use a small drill bit again and work up to one just a bit smaller then the screw:
http://i99.photobucket.com/albums/l287/beeza2/100_1466.jpg
Done!
http://i99.photobucket.com/albums/l287/beeza2/100_1468.jpg
http://i99.photobucket.com/albums/l287/beeza2/100_1495.jpg
Dont mind the door trims,just painting em':
http://i99.photobucket.com/albums/l287/beeza2/100_1494.jpg
http://i99.photobucket.com/albums/l287/beeza2/100_1493.jpg
Perfect.Removing CD's? No problem!
http://i99.photobucket.com/albums/l287/beeza2/100_1516.jpg
Make sure you Reset the ECU (http://www.ozhonda.com/forum/showthread.php?t=67113) afterwards if you removed the back up fuse or the negative cable on the battery.
Other comments:
atm I'm using the power cord that plugs into the cigarette lighter,it's messy and ugly.I will wire the power cord up to a power source and post the results.
I'm Lovin' it! hehehe
:honda: