Shin2chou's EK4 B16a2 Turbo

[FastFwd]

So im currently building Shin's turbo setup. Progress so far...

Installed

Greddy Cast Iron Log manifold
Greddy Intercooler
Garret Gt28rs (disco Potato)
Trust Air Cleaner
Braided Oil lines
Water lines
Vac lines
2.5inch Front and Dump pipe Stainless
Turbo Smart Dual Port BOV
Half of the cooler piping
GFB Boost controller
Full service (Oil, Oil filter, plugs)

Awaiting

Odb2a to Odb1 Convertion harness install the Hondata s200 ECU
Custom 2.5 inch intercooler piping


Man Hours spent so far
11

Flix

http://imgur.com/XCAWr.jpg

http://imgur.com/EabGq.jpg

http://imgur.com/k6fbV.jpg

http://imgur.com/OSZtB.jpg

[FastFwd]

Currently looking for a Odb2a female to odb1 male conversion harness to make the ek4 fit on the hondata s200 that came from a japspec b18c

wtd post below

http://www.ozhonda.com/forum/showthread.php?132357-odb2a-to-odb1-convertion-harness&p=2736297#post2736297

[FastFwd]

move to the build section when possible pls

[IEVAQ8]

y u running such a small dump and front pipe.??????

if its stock engine with 10.1 comp, 3inch would be a minimum requirement to get as much exhaust gas out as possible......especially when running a log manifold which creates heaps of back/manifold pressure that honda's dont like.....

[FastFwd]

y u running such a small dump and front pipe.??????

if its stock engine with 10.1 comp, 3inch would be a minimum requirement to get as much exhaust gas out as possible......especially when running a log manifold which creates heaps of back/manifold pressure that honda's dont like.....

Sorry correct myself its 3inch dump and 2.75inch front pipe and he already has an existing 2.5inch xforce stainless exhaust.

The dump and front came with the prepurchased kit, i've told shin to change the front pipe to 3inch to the cat and possibly leave his 2.5inch exhaust as he will only be running max 8psi on the high comp stock setup.

[IEVAQ8]

Sorry correct myself its 3inch dump and 2.75inch front pipe and he already has
an existing 2.5inch xforce stainless exhaust.

The dump and front came with the prepurchased kit, i've told shin to change the front pipe to 3inch
to the cat and possibly leave his 2.5inch exhaust as he will only be running max 8psi on the high comp stock setup.

yeh, as u recommended, i would be running 3 inch dump and front and also a 3 inch cat (highflow, or guttered) as a minimum,
and if there is a tight budget stick with the 2.5inch cat back, but preferably a 3inch cat back too....

[Benson]

I ran 2.5inch Dump and Front pipe on my last Turbo B16a motor. Motor made a good 160kw at the front wheels.

[FastFwd]

Boost guage installed
Intercooler piping finished.
S200 Hondata with Conversion harness installed

Now just waiting on a tune to see the HP numbers this week some time.

[BIGTYM]

Im interested in seeing what numbers this makes as compared to my setup? Im running same manifold but with a Greddy TD-05.

[shin2chou]

hahha you put it up ;D

[dny]

did you know shin2chou is the prince of taiwan? he pockets this kind of money to do up his on-the-side-car daily

[FastFwd]

lol why he rolling in a civic and not a s class merc?

[Lukezen27]

Nice work bro. :)

I’ve been bugged many times to do a turbo setup but I’m way to scared of braking someone else’s car lol

My car fok it hahah live and learn hahah

[FastFwd]

Nice work bro. :)

I’ve been bugged many times to do a turbo setup but I’m way to scared of braking someone else’s car lol

My car fok it hahah live and learn hahah


Nah fairly confident with my work these days...especially D and B series, know them inside out.

[shin2chou]

tunes booked for the 18th btw via sean at allstar

[FastFwd]

tunes booked for the 18th btw via sean at allstar

Pretty excited for ya man...

[dny]

yeh im pretty excited too! better take me

[J-Spec23]

ill tag along ! LOL

[shin2chou]

is that you jon?

[success]

cool car.. does it come in running

[IEVAQ8]

how did the tune go???

[Lukezen27]

Nah fairly confident with my work these days...especially D and B series, know them inside out.

Might have to start offering my services after seeing just how many people are get ripped-off in regards to turbo installation..
D and Bs are also my forte!
Problem is, more people are all talk and time waster!
Unlike us rare few that actual do what we say where going to do hahah

[FastFwd]

Might have to start offering my services after seeing just how many people are get ripped-off in regards to turbo installation..
D and Bs are also my forte!
Problem is, more people are all talk and time waster!
Unlike us rare few that actual do what we say where going to do hahah

Yeah ive had alot of all talk and time wasters but shin came up with the goods and was ready to do it. Yeah the problem with shops is they have large overheads so they have to charge large ammounts of labour costs. But sometimes i dont know where they get there figures from. Some charge like $110-130 an hour which honestly if its something i can do the same if not better i dont think they should be charging that much.

[BIGTYM]

Updates on tune / build???

[success]

update plx shin_chou

[shin2chou]

still got a few things to fix up before it hits full potential, but currently making 123kwatw

[Lukezen27]

still got a few things to fix up before it hits full potential, but currently making 123kwatw

less than my turbo stock D so keep going man..

What's next on the upgrade list?

[alanalan]

nice ek4maen

[Jye]

Any vids? Would love to see this car in action!

[gambate]

injector max'ed out... i heard