View Full Version : DC2R Offset?
Hey everyone, what offset would sit flush with the guards on a dc2r, wouldn't mind a little bit of camber but nothing too ridiculous. I want to run 16's 5x114.3, tyres 205/45/16
Thanks
geeang
02-05-2010, 10:14 PM
with 205/45/16 I reckon you could run around +30-33 with minimal guard rolling, no crazy camber either.
with 205/45/16 I reckon you could run around +30-33 with minimal guard rolling, no crazy camber either.
Is this based on 6, 7,8,9,10 inch width wheels?
geeang
02-05-2010, 10:54 PM
Is this based on 6, 7,8,9,10 inch width wheels?
My bad, common 16x7 size.
Well it would be around 16x7 - 16x8 or in between
kairi_k
04-05-2010, 09:34 PM
16x7 +40 offset perfect look
1900-hustler
05-05-2010, 04:27 PM
+38 to 42 is sensible - but sits inside the guards..
with a type profile of 50 or above you might need some rolling done
id be going low 30s like geeang said
xntrik
09-05-2010, 06:33 PM
16x7 +30 will scrub. Need rear guards rolled on stock camber.
16x7 +38 will just clear. Not too low though.
firepower
09-05-2010, 08:13 PM
When you say flush, are you referring to the hellaflush look? If you are, you need to go 8" wide and 30 offset. I am looking to do this on my 98 spec ITR and CCW recommended this to me but i must run 0 camber for the hellaflush look. You definitely need to roll your guards though.
firepower
09-05-2010, 08:13 PM
Oh to add, every wheel is different, you need to try them on as it's a trial and error thing. Hope this helps :)
yeah man hella flush look
firepower
11-05-2010, 06:12 PM
yeah man hella flush look
Hellaflush look requires guard rolling. You can't get away without doing it.
If you want to go crazy width and offset, you might even need to resort with guard flaring. My other mate fitted on evo 5 wheels on his euro r accord and it guard rubbed badly. Evo 5 wheels are 17x8 35 offset so that might be a guideline. You can't achieve the hellaflush look with most 16x7 without lower offset or spacers to get em out to my experience.
G-Stick
11-05-2010, 06:57 PM
reasonable fitment, 16x7 +35 minimal guard rolling
ive got 16x7 +42 te37s with 25mm spacers.. sits flush with rolled guards and shaved bumper tabs
firepower
11-05-2010, 08:34 PM
reasonable fitment, 16x7 +35 minimal guard rolling
ive got 16x7 +42 te37s with 25mm spacers.. sits flush with rolled guards and shaved bumper tabs
Yup exactly what i said. 42 offset wheels with 25mm spacers means that your offset is only 17+. Sick! :)
Some sick S2K on hellaflush
http://fatlace.com/hellaflush/car-events/glimpse-of-one-of-one-atl.html
Depends how much camber your running also.
How many degrees duy?
vtecing
13-05-2010, 09:09 AM
can someone post pics of their set up and specs please. Would you need different offset to get both front/rear flush?
firepower
30-08-2010, 08:40 AM
http://i130.photobucket.com/albums/p257/10KRPM/40978_1461329928199_1081972223_1330803_3817777_n.j pg
17X8 30 offset on front -1.5 camber
http://i130.photobucket.com/albums/p257/10KRPM/34027_1409697117411_1081972223_1193078_1388443_n.j pg
17x8 35 offset on rear -2.2 camber
Pics was when guard wasn't rolled. Now rolled so can actually accomodate 17X9s or lower offset ..x8s
Hope this helps.
Powered by vBulletin® Version 4.2.2 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.