ECU-MAN
18-12-2004, 11:39 PM
Disclaimer: The following is provided as a GUIDE ONLY, and neither myself nor Ozhonda take any responsibility for the outcomes of someone else doing the following. You follow these steps at your own risk!
Aim: remove radio from a DC2 Intergra.
Required: philips head screw driver, flat head screw driver,
step 1
undo the 2 x screws at the back of the center consol, one either side
http://ecu-man.com/diy/dc2radio/IMG_0028.jpg
Step 2
using a flat head screw driver gently lift the cover
http://ecu-man.com/diy/dc2radio/IMG_0029.jpg
Step 3
undo the two screws
http://ecu-man.com/diy/dc2radio/IMG_0030.jpg
Step 4
Lift the handbrake lever and lift out the center console, Remove the ash tray and Undo the two screws shown below one either side. remove the gearshift knob , turn anti clockwise
http://ecu-man.com/diy/dc2radio/IMG_0031.jpg
Step 5
Undo the two screws shown below.
http://ecu-man.com/diy/dc2radio/IMG_0032.jpg
Step 6
remove the ashtray assembly, and undo the wiring harness holding it on ( see
blue arrow ) then remove the two scews ( green arrows )
http://ecu-man.com/diy/dc2radio/IMG_0033.jpg
Step 7
pull out console.
http://ecu-man.com/diy/dc2radio/IMG_0039.jpg
Step 8
undo the radio screws under the back of the radio
http://ecu-man.com/diy/dc2radio/IMG_0036.jpg
pull the radio out, replace with new one and reinstall in revers order.
happy stereo removal :)
Disclaimer: The following is provided as a GUIDE ONLY, and neither myself nor Ozhonda take any responsibility for the outcomes of someone else doing the following. You follow these steps at your own risk!
Aim: remove radio from a DC2 Intergra.
Required: philips head screw driver, flat head screw driver,
step 1
undo the 2 x screws at the back of the center consol, one either side
http://ecu-man.com/diy/dc2radio/IMG_0028.jpg
Step 2
using a flat head screw driver gently lift the cover
http://ecu-man.com/diy/dc2radio/IMG_0029.jpg
Step 3
undo the two screws
http://ecu-man.com/diy/dc2radio/IMG_0030.jpg
Step 4
Lift the handbrake lever and lift out the center console, Remove the ash tray and Undo the two screws shown below one either side. remove the gearshift knob , turn anti clockwise
http://ecu-man.com/diy/dc2radio/IMG_0031.jpg
Step 5
Undo the two screws shown below.
http://ecu-man.com/diy/dc2radio/IMG_0032.jpg
Step 6
remove the ashtray assembly, and undo the wiring harness holding it on ( see
blue arrow ) then remove the two scews ( green arrows )
http://ecu-man.com/diy/dc2radio/IMG_0033.jpg
Step 7
pull out console.
http://ecu-man.com/diy/dc2radio/IMG_0039.jpg
Step 8
undo the radio screws under the back of the radio
http://ecu-man.com/diy/dc2radio/IMG_0036.jpg
pull the radio out, replace with new one and reinstall in revers order.
happy stereo removal :)
Disclaimer: The following is provided as a GUIDE ONLY, and neither myself nor Ozhonda take any responsibility for the outcomes of someone else doing the following. You follow these steps at your own risk!