beeza's DIY's

[beeza]

Thought I would put all my efforts into 1 thread in an effort to get other's motivated to do some DIY's and other useful info n' stuff :D (also a quick reference)

:honda:

MORE AIRFLOW THROUGH THE HEAD:

http://www.ozhonda.com/forum/showthread.php?188655-More-airflow-through-the-head&p=3989142#post3989142

Calibrating The Voltage on the TPS (http://www.ozhonda.com/forum/showthread.php?120191-DIY-Calibrating-the-Voltage-on-the-TPS)

Gettin' Ya Gaps right! (http://www.ozhonda.com/forum/showthread.php?118376-DIY-Gettin-Ya-Gaps-Right!)

Get that lip sitting straight (http://www.ozhonda.com/forum/showthread.php?102747-DIY-Get-that-lip-sitting-straight.)

Adjusting Ignition Timing (http://www.ozhonda.com/forum/showthread.php?120425-DIY-Adjusting-Ignition-Timing)

MSD Ignition System Install (http://www.ozhonda.com/forum/showthread.php?119576-DIY-MSD-Ignition-System-Install)

Modifying the stock distributor cover to accept an external coil (http://www.ozhonda.com/forum/showthread.php?138076-Modifying-the-stock-distributor-cover-to-accept-an-external-coil)

You Have Cleaned the IACV BUT Your Idle Is Still High/Erratic? Adjust The FITV. (http://www.ozhonda.com/forum/showthread.php?120938-You-Have-Cleaned-the-IACV-BUT-Your-Idle-Is-Still-High-Erratic-Adjust-The-FITV.)

Header Wrap (http://www.ozhonda.com/forum/showthread.php?133321-Header-Wrap)

Modifying the stock Throttle body for more air flow (http://www.ozhonda.com/forum/showthread.php?132174-Modifying-the-stock-Throttle-body-for-more-air-flow)

Repairing stripped threads on the head from those DAMN Valve cover bolts! (http://www.ozhonda.com/forum/showthread.php?121671-Repairing-stripped-threads-on-the-head-from-those-DAMN-Valve-cover-bolts!)

Breathing Fresh Air (finally) (http://www.ozhonda.com/forum/showthread.php?93744-Breathing-Fresh-Air-(finally))


Also:

Bushes - Replaced the major ones (http://www.ozhonda.com/forum/showthread.php?120991-Bushes-Replaced-the-major-ones!)

Honey,I steamed cleaned the car! (http://www.ozhonda.com/forum/showthread.php?107865-Honey-I-Steamed-Cleaned-my-Car!)

Antenna Removal while keeping the stock look! (http://www.ozhonda.com/forum/showthread.php?123622-Antenna-Removal-while-keeping-the-stock-look!)

Custom Mount for a GPS (http://www.ozhonda.com/forum/showthread.php?122585-Custom-Mount-for-a-GPS)

How to tell the year of an engine (http://www.ozhonda.com/forum/showthread.php?125923-How-to-tell-the-year-of-an-engine)

Stuff that's been sucked into the Throttle Body!! (http://www.ozhonda.com/forum/showthread.php?113980-Stuff-that-s-been-sucked-into-the-Throttle-Body!!)

My Boot/Rear seat (http://www.ozhonda.com/forum/showthread.php?92436-My-Boot-Rear-seat)

Claybar's are incredible (http://www.ozhonda.com/forum/showthread.php?111154-Claybar-s-are-Incredible!-buffing-buffed-clear-coat)

Fake Pivot Raizins (http://www.ozhonda.com/forum/showthread.php?131876-Fake-Pivot-Raizins)

Reviews/products:

Cusco H Brace (http://www.ozhonda.com/forum/showthread.php?126496-Cusco-H-Brace)

Pivot Raizin Volt Stabilizer (http://www.ozhonda.com/forum/showthread.php?76901-Review-Pivot-Raizin-Volt-Stabilizer)

Cusco Brake Stopper (http://www.ozhonda.com/forum/showthread.php?69104-Cusco-Brake-Stopper)

X-Force Headers,Muffler + Magnaflow Hi Flow cat Installed, with sound clips (http://www.ozhonda.com/forum/showthread.php?76097-X-Force-Headers-Muffler-Magnaflow-Hi-Flow-cat-Installed-with-sound-clips)

Universal Strut Bar Lower Rear Cross Floor Bar Sway (http://www.ozhonda.com/forum/showthread.php?85147-Universal-Strut-Bar-Lower-Rear-Cross-Floor-Bar-Sway)

Teddy Bear Rear bar Hangin' (http://www.ozhonda.com/forum/showthread.php?126497-Teddy-Bear-Rear-bar-Hangin)

Travels:

http://www.ozhonda.com/forum/showthread.php?155117-A-Few-pics-of-Inner-and-Outer-Tokyo-areas

Beeza does Melbourne,the Yarra Valley,dandenong ranges and Phillip Island! (http://www.ozhonda.com/forum/showthread.php?131971-Beeza-does-Melbourne-the-Yarra-Valley-dandenong-ranges-and-Phillip-Island!)

My thread:

The Batmobile (http://www.ozhonda.com/forum/showthread.php?59606-The-Batmobile)

Enjoy! :thumbsup:

btw ever wondered how that damn PCV system works?

"Purpose of the PCV system
During each compression stroke a small amount of gas seeps past the piston rings. These gasses comprise of an unburnt fuel/air mixture which contaiminates your engine oil and corrodes your internal parts. The purpose of the PCV system is to remove these gasses while maintaining emissions standards.
The PCV valve tested is known as a variable-flow PCV valve. This valve allows the crankcase to evacuate gasses into the intake manifold even at high load conditions.
The problem Honda engineers had was the following:
They needed to find a vacuum source which provides a variable vacuum with less draw at idle and more vacuum pressure pulling gasses out at high load (WOT) conditions. The dilemma is that at Idle and low load conditions the vacuum present inside the Intake manifold is the greatest and at WOT the vacuum in the intake manifold is the lowest(almost none). This is the exact opposite of what is needed because their is more blowby gasses needed to evacuate at WOT (high load) then at Idle!
So they designed a special spring loaded pintle valve(PCV valve) which does the following:
Idle, Low load--- high vacuum pressures fully retract the pintle causing only a small vacuum draw on the crankcase.
Mild load conditions--- vacuum present in the intake manifold is not as strong so the pintle sits in the middle of the pcv valve allowing more vacuum to evacuate the crankcase.
High load + WOT conditions--- their is almost no vacuum present and the pintle is almost completely extended allowing the most amount of gasses to be drawn into the intake manifold.
Engine backfire--- the pintle fully extends and seals to eliminate any gasses from flowing from the intake manifold to the crankcase.
Under acceleration and high load situations blowby is extremely high and consequently the PCV valve/purge hose cannot supply enough vacuum to remove all the gasses needed. This is when the flow reverses from the valve cover to the intake. Their is so much blowby present that both the PCV valve/purge hose and the Valve cover breather/hose have to both vent excess pressures created. The PCV is working at its best but can't keep up with the demanding pressures created."

This product looks GREAT:

http://www.theoldone.com/components/breather/

[_CRX_]

A lot of great info here ....WELL DONE

[tiksie]

Good stuff :)

[beeza]

Sharing is caring.

Thanks guys,get stuck in! :)

[beeza]

bump this up!

[specialst]

mods. i think this deserves status as a sticky thread.

[beeza]

Hey,Thanks a lot man! :)

[wynode]

Probably really should be part of this thread:
http://www.ozhonda.com/forum/showthread.php?82672-Definitive-guide-to-D.I.Y-Updated-03-11-Under-review

That said, very good info in here. Great work beeza! PM the mod of this forum and he will take care of it :)

[beeza]

Cheers Wyn and thanks for your support always too mate.

I PM'ed Kiki :)

[m3ntAL_l2]

nice amount of infor there beez

FYI Kiki is rarely on here now days, prob best to PM Drew directly to have the items sorted or a super mod

[beeza]

Cheers mate,I thought as much but there's no rush.

If anyone is keen,they will find em'

[~Sp33~]

beeza's Japan and Hong Hong Trip Pics

beeza's Japan Pics 24th Nov - 3 Dec 2009

Links don't work - i'm disappoint.

[u mad?]

Back to the dream time

[beeza]

It looks like the threads have been removed.

Not sure why...if a mod can check it out for me that would be great Thanks.

[beeza]

bump it up 4 da noobs!

Added in the travels bit,pics of inner and outer tokyo area's (old thread)..

Hi Guys! long time no speak.. :)

[Vvvtec]

Beeeeeeeeeza

Welcome back man!

[RenzokukenJ]

Dassssssssss it

[cbauto]

hi beeza, remember me?

[beeza]

Yes! I remember Ya'll!

Been a while.. Still the the Blue EK sedan,with the d16y4 but manual now! The old engine died due to a slight crank pulley oil seal leak that decided to go bad and dump all the oil in a 5 hr drive then due to oil starvation one of the main bearings spun.Hell of a knocking sound,mates had to rescue me from Kempsey lol 12 hr return trip on a flatbed trailor,$80 + petrol.2 free d16y4 engines off darrel (EK4-guy) and SHO (we all know him :) ) + I had the pedals from our day out with Mike:http://www.ozhonda.com/forum/showthread.php?59606-The-Batmobile/page150

haha sorry Mike LOL

[beeza]

diy added.

[JH22A]

diy added.

Great info thanks mate will be using some tips for sure.

[beeza]

Ah,good stuff. Thank U.

[webbrowan]

Thanks for sharing this comprehensive list of info which is definitely useful in many practical ways. At times we need more than just a piece of advice and it could get difficult scavenging through this entire forum in search of multiple data. Hence, to compile everything together would definitely help to save time and effort.

[beeza]

Always thinking of others :)

Yes,5 yrs of diy in 1 thread,forsure.

Thanks man.Makes me wanna put some more good stuff in here.

[beeza]

Always thinking of others :)

Yes,5 yrs of diy in 1 thread,forsure.

Thanks man.Makes me wanna put some more good stuff in here.

[ep3rsteve]

Thanks for sharing this comprehensive list of info which is definitely useful in many practical ways. At times we need more than just a piece of advice and it could get difficult scavenging through this entire forum in search of multiple data. Hence, to compile everything together would definitely help to save time and effort.

Ello webbrown your post makes me want to take out a loan with the smarter finance company I need 250k to preorder 2017 NSX and I work part time at KFC can you please arrange thankyou you are the best I will recommend you to the whole of ozhonda wow smarter finance company is THE GREATEST!!!!!!!!!!!!

https://c2.hornblasters.com/products/HB/SPORTS/airhorn_l.jpg

[beeza]

Leave all that crap outta here mate.Take it to spam.