b18c2 head

[jayeg]

i recently had a new timing belt put on my car i was driving it yesterday and the timing belt skipped and shredded both my cams would this have cause any damage to the bottom end or just the head

[mocchi]

i recently had a new timing belt put on my car i was driving it yesterday and the timing belt skip and shredded both my cams would this have cause any damage to the bottom end or just the head

LMAOOO. sorry for laughing but i know why it skipped.

-you didnt adjust belt tension
-probably turned motor clockwise, tensioner only work 1 way (CCW).
-you didnt verify belt tension after hand crank 5-6 crank revolutions.

next time please have your service manual handy when working on precise component like timing belt.
no one here can tell if block is fine or not. you gotta open it up and see for yourself.

[Vvvtec]

Sounds like you need a head job

[chauster]

Bad luck bro. I hope the mechanic did it and not you. Just go back and tell them. They should supply and fit new engine for you. This happened to a fries T Honda.

[jayeg]

no i did not do the timing belt a shop did i took the head off cause the timing belt snap and i check the head everything was ok put the head back togther then got the timing done at a shop i dont see why everybody is putting sh*t on me im learning and asking i thought that was what the site was for my question hasnt even been answered i will pull the head off and see if the is any damage to the the block or pistons and start looking for a new head

[Bludger]

no i did not do the timing belt a shop did i took the head off cause the timing belt snap and i check the head everything was ok put the head back togther then got the timing done at a shop i dont see why everybody is putting sh*t on me im learning and asking i thought that was what the site was for my question hasnt even been answered i will pull the head off and see if the is any damage to the the block or pistons and start looking for a new head
You need to ask questions that people can answer.

No one can tell you weather your engine if ****ed or not.

[jayeg]

i no nobody can tell if its stuffed i was just asking incase it had havnt to someone else the motor still
cranks the cams are turning the compents are still turning it just wont start im thinking maybe the vavles got bent
or the timing is out when the belt skipped any help or advice would be a helpfull thanks i

[mocchi]

i no nobody can tell if its stuffed i was just asking incase it had havnt to someone else the motor still
cranks the cams are turning the compents are still turning it just wont start im thinking maybe the vavles got bent
or the timing is out when the belt skipped any help or advice would be a helpfull thanks i

rev it to 9000. see if it's good or not. if nothing happens while revving then you know your second daily still fine.

or you can open head to verify damage.

either way, I wish you luck.

Sean.

[Bludger]

rev it to 9000. see if it's good or not. if nothing happens while revving then you know your second daily still fine.

or you can open head to verify damage.

either way, I wish you luck.

Sean.thats one powerful starter motor.

where do you get them..

makes you think, why bother with n engine, just drive your car with the starter motor....

[chauster]

I seen it in YouTube . Some guy had a toda starter motor and no engine. It ran 15s in an eg. Not too bad.

On topic. Your engine is stuffed. Wouldn't bother.

[jayeg]

took the head off today vavles arnt damaged the pistons werent damaged either was the bore.
tomorow gonna jack it up and crank it is there anything i should be listen to or looking for besides making sure the pistons are
moving

[GSi_PSi]

Are the spark plugs okay ?, does it have enough fuel ?. The ecu good ?.

[na-118]

if a shop did the timing belt job then why are you doing all the work ? driveway warranty?

[jayeg]

i rang the shop they said its not there fault and they wont fix it i jacked the car up today turned the wheel pistons are
moving fine and i cant hear anything and they are smooth when moving the spark plugs are still fine im just waiting to find
a head for a good price cause i dont no if i can get the head machined or not it was pretty badly damaged on the end where the
cams gear are.

[na-118]

have you tried sorting it out with fair trading nsw?

bar the motor by hand,, crack test the block and head,, it's not as simple as some people put it out there when timing belt snaps

[jayeg]

we turned the motor by hand and the bottom end is fine the head is stuffed the belt didnt snap the timing was done
wrong by the shop must have went loose and the second cam skipped and shredded the end of the cams near the cam gear im
looking for a new head at the moment

[na-118]

pm vtec1987 he might have a head lying around

[jayeg]

update took it to a head reco shop he said the for some reason the head wasnt getting oil thats why the cam skipped because it was
not getting any oil and running dry so it wasnt the timing any thoughts what it could be anybody had this happen before ,i will check the
oil pick up

[Bludger]

update took it to a head reco shop he said the for some reason the head wasnt getting oil thats why the cam skipped because it was
not getting any oil and running dry so it wasnt the timing any thoughts what it could be anybody had this happen before ,i will check the
oil pick up
I still don't get why you're asking a forum that has never seen your engine....

all the while the evidence is right in front of you.....

[na-118]

if it's been running dry best if you check oil pump while you're at it,, severe scoring backlash etc

[jayeg]

yeah i will its weired the car was running fine for a week. and then that cams fryed. when i check the pistons there arnt burnt and the block is fine what im i looking for when i check the oil pump hope i find the prob asap sold my other car and then this happens

[na-118]

well first drain the oil,, if you find little bronze pieces you have just scored the liners and bearings pretty hard,,

a smashed oil pump is what youre looking for,,,there is more to it

[na-118]

http://img521.imageshack.us/img521/7436/24832310150218004763482.jpg (http://imageshack.us/photo/my-images/521/24832310150218004763482.jpg/) Uploaded with ImageShack.us (http://imageshack.us)

that was my oil pump housing absoloutley rooted along side with the gears,

[jayeg]

ok i will take it apart and have a look thanks