DIY Stock EK LIfters

[viinnh]

Disclaimer: The following is provided as a GUIDE ONLY, and neither myself nor Ozhonda take any responsibility for the outcomes of someone else doing the following. You follow these steps at your own risk!


Aim: Lift your stock wing up a bit
Required: spacers/nuts/gromets
Steps:
-Remove your stock EK wing by removing the plastic under the boot then the 4 screws

-Then lift up the wing and add your spacers/nuts/gromets what ever you prefer to use on the outer stud (closer to brake light) now use the nut from the wing and bolt it on the same stud you put them spacers/nuts/gromets on.
http://i40.tinypic.com/2eaiav8.jpg

-Now bolt the wing back on and its lifted :P

Other comments
Make sure when bolting back on the 2 nuts on the studs, it covers and sits flush on the hole to prevent water leaking in.
http://i40.tinypic.com/wmi9w.jpg

BEFORE:
http://i40.tinypic.com/qydeg6.jpg
AFTER:
http://i39.tinypic.com/axmfif.jpg
http://i43.tinypic.com/4qix52.jpg

YES I KNOW ITS POINTLESS TO SOME PEOPLE. I THOUGHT ID SHARE
AND YES THIS WOULD WORK ON A SPOON REP WING

For EK9 Wing refer to this DIY I have made.
http://www.ozhonda.com/forum/showthread.php?174713-DIY-EK9-Wing-lifters

[kyzz]

Looks good bro subtle but noticable

[NeedVtec]

reckon it would work for an eg wing?

[viinnh]

nah it wont work on a eg as it does not have the rear bolts , its 4 bolts in a line on a eg.


also lifted it more yoo
http://i44.tinypic.com/1604k82.jpghttp://i42.tinypic.com/2dkmgz7.jpg

[kyzz]

what did you use to lift it

just a nut or something hahaha

[viinnh]

4 spacers + oem nut duct tape together and slid on :P

[kyzz]

looks fukn mean man when i get my hands on my spacers ill give it a go

[marcoleeau]

4 spacers + oem nut duct tape together and slid on :P
What is the spacer size?

[EK4VTEK]

nah it wont work on a eg as it does not have the rear bolts , its 4 bolts in a line on a eg.


also lifted it more yoo
http://i44.tinypic.com/1604k82.jpghttp://i42.tinypic.com/2dkmgz7.jpg

haha that look awesome. well done mate. i went and bought me OEM ek9 wing coz i hated the look for the ek4 spoiler. i shuda done that tho.

[5thgen_prel]

where do u get the spacers from??

[viinnh]

thier just washers from bunnings or any warehouse

[kyzz]

im trying it now, do you still bolt the boot to the wing or do you just put the nut ontop of the spacers and let it sit in the holes its supposed to be bolted to and only the nuts closer to the front of the car are holding the wing down/ if you know what i mean

[viinnh]

only the 2 front bolts (closer to the front of the car) are bolted down. the other bolts are with the spacers on the stud and sits on top of the hole to prevent water from getting in

[kiaa_]

Probably going to give this a go tomorrow :)

[VIP-EK]

Gave it a go today. Turned out pre good
http://s21.postimg.org/stmq0j39f/image.jpg (http://postimg.org/image/stmq0j39f/)

[eren]

Too easy lol =)
http://img.tapatalk.com/d/13/04/10/aha5a5a7.jpg

http://img.tapatalk.com/d/13/04/10/asa4y4y3.jpg

[Adamjoeldavis]

what size washers? 1/4''? and stupid question but does doing this reduces the clearance when you open the hatch/boot?

[VIP-EK]

what size washers? 1/4''? and stupid question but does doing this reduces the clearance when you open the hatch/boot?

Use what ever washers, doesn't even need to be washer. I just threw on some bolts over it then put the original bolts over it.

[viinnh]

use anything you want doesnt matter. and no does not reduce any clearance

http://www.ozhonda.com/forum/showthread.php?174713-DIY-EK9-Wing-lifters

here is a DIY i made for EK9

[iceey]

http://i1160.photobucket.com/albums/q495/xXiceeyXx/image-5.jpg

Done it to mine .. Great DIY mod man thnx

[Chalabi]

Need parts for my ek please see thread

[jprak]

Need parts for my ek please see thread

stopped hijacking this thread. if you want to promote, bump your thread