CAI EG Sedan

[aimre]

The other weekened i decided to put in a CAI,
i removed the fron bar, put in the tube, tried to put the bar back on but couldnt as the tube wouldnt fit.
I then relocated the horn, the bar now fits but the pipe is abit squished.

is there n e where else i can put it ? somehow?:confused::confused:

thanx:wave::wave:

This is what ive done:

We moved this: http://img.photobucket.com/albums/v47/aimre/horn.jpg

To Fit this:
http://img.photobucket.com/albums/v47/aimre/CAI.jpg

This is me being an idiot :D:D:D:p:p:cool::cool: hahaha:

http://img.photobucket.com/albums/v47/aimre/mewithpipe.jpg

[DRCVIC]

"hmm, now what can we use for a bong?" i know... the resonator for the stock air intake!

[joneblaze]

ROFL... you look like the ultimate "lad"
Btw, that crumple ass "piping" won't perform as a very trustworthy or reliable intake...

[aimre]

WHy not?
What should i use?

[|N|]

should at least keep the pipe as little bent as possible...

[aimre]

i know i should BUT HOW?
Eg sedan doesnt have those mad fog light holes

at least its got less bends that the orriginal (remember its not a ram but CAI)
so really it doesnt mateer how mane bends u got... right?

[|N|]

u might want to pm egSi... he s got taht set up ..... and he did a DIY write up a while ago ... u might want to check that too...

[egSi]

yeah nicks right.

man that is some absolutely ****ed up pipe man :D

there is some better pipin around. looks to me that u have got like 'air ducting' sorta hose :thumbdwn:, jons right that shit is weak, u need more 'irragation' sorta hose. SIMILAR ribbed shit but tougher and can hold much smoother bends.

what filter did u get aimre? why didnt u get it off me u terd :p :D

[aimre]

i got no other filter, its air ducting that runs to the stock box
(dont worry trav, ill always buy my stuff from u:))

[egSi]

i got no other filter, its air ducting that runs to the stock box
(dont worry trav, ill always buy my stuff from u:))

man hit me up if u want a K+N panel cheap ;)

[|N|]

man hit me up if u want a K+N panel cheap ;)

yea u need some thing other then stock ... coz the stock ones r ghey.. u wont get much out of the CAI... ohh.. by the way pls let ne know if u can get hold of some nice material for the ductin pipe....

[egSi]

yeah man dont get 17s and yes bulk buy :D

15s would be dope man!!

16s is meh BUT much better than 17s. ;)

[aimre]

or mayb the wheels u got


N E WAY.... what do i do bout this CAI??
Where do i put it?

[Steer^Gimic]

i did mine the other week. compliments of *cough* car lovers vacuum *cough*
i mean, i went and um...bought it..yes.
where you have it shouldnt be a prob, but with sturdier pipe and less bends, it wont looked as messed up.
cheers

[egSi]

or mayb the wheels u got


N E WAY.... what do i do bout this CAI??
Where do i put it?

its in an OK place its the shit pipin we r all whingin about, pm 'nedgeworth'

he was doin the same thing, i think he relocated his horn too, he has eg sedan and got an K+N panel off that cool underground guy ;)

[nedgeworth]

y0. heard you needed some help. All i did was extend my horn wires and run it through the bar along the front then mount the horn on the opposite side. There should be a bolt hole so it's just a direct bolt on. hardest part is running the wires through the small section of bar unless you get lazy and just use cable ties. It's pretty simple to do.

As everyone else has said get some different pipping. I got some from my local hardware store. had holes in it so just wrapped it in some plumbing tape all the way down to cover the holes. works a treat man :D

[bennjamin]

just remember guys.

The pipings surface is not so relevant to flow ( rough is actually better than smooth) - JUST as long as the pipe will remain a constant diameter , and wont deform at all .( try to get some thicker , stronger flexpipe etc....a OEM intake pipe works best :))

Good luck guys.

[|N|]

just remember guys.

The pipings surface is not so relevant to flow ( rough is actually better than smooth) - JUST as long as the pipe will remain a constant diameter , and wont deform at all .( try to get some thicker , stronger flexpipe etc....a OEM intake pipe works best :))

Good luck guys.

how should i go about gettin such pipe??

[egSi]

go to the 'irrigation' section in bunnings nick :thumbsup:

i think i might do a diy on this lol

[bennjamin]

how should i go about gettin such pipe??

a pipe , jus tlike your intake pipe ( the oen ffrom the airbox to the throttle body ) is perfect for such a thing.

Try and find a EK4 or dc2 spare intake pipe arm....and use that :)

[egSi]

woops, my bad nick :o

[|N|]

u know that 'U' shape thingy under the air box... well i took taht out when i first bought my car... coz i see no point of havin it there.... at least for me.... so u guys reckon i could use that? like cut it up and stuff?

[egSi]

u know that 'U' shape thingy under the air box... well i took taht out when i first bought my car... coz i see no point of havin it there.... at least for me.... so u guys reckon i could use that? like cut it up and stuff?

nah man go to BUNNINGS!! and get some pipe like me!!

u want me to do a bloody diy on it nicK? lol

[aimre]

yes do it trav

i still dont exactly understant whats wrong with the piping....
why does it need to be more solid...

[|N|]

nah man go to BUNNINGS!! and get some pipe like me!!

u want me to do a bloody diy on it nicK? lol

oh.. yes pls...

[egSi]

ok maybe