learner
12-03-2005, 04:11 AM
just installed the tower bar got it from last week.
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar01.jpg
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar02.jpg
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar03.jpg
here is how i do it...
P.S. i am not a professional... so if there are any mistake. pls correct me.
1. un-tight a little bit the bolts on the tower bar which holds
the blue part (both side). so you able to adjust the angle of
it when you put it in
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar04.jpg
2. un-tight these 3 bolts in your car. (both side)
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar05.jpg
3. put the bar in place
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar06.jpg
4. here are pic on the driver's side. you can see is very
close to the holes.
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar07.jpg
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar08.jpg
5. the cusco manual says you can un-tight these 2 bolts
to adjust the holes about 3mm away from the tower bar.
(but i couldnt do tat)
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar09.jpg
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar10.jpg
6. so instead move the holes, i put some felt on the holes to
stop they touch each other.
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar11.jpg
7. use your hand to put the bolts back in place (both side)
**push the silver part down and tight the screws again using your
hand until you can't turn the bolts anymore**
then now you can use tools to tight it. remember dun over tight it,
otherwise you will snap the bolt.
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar12.jpg
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar13.jpg
8. NOW tight the screws on the tower bar (both side)
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar13b.jpg
9. the sticker :D
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar15.jpg
here are some of the pic
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar14.jpg
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar16.jpg
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar17.jpg
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar18.jpg
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar19.jpg
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar01.jpg
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar02.jpg
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar03.jpg
here is how i do it...
P.S. i am not a professional... so if there are any mistake. pls correct me.
1. un-tight a little bit the bolts on the tower bar which holds
the blue part (both side). so you able to adjust the angle of
it when you put it in
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar04.jpg
2. un-tight these 3 bolts in your car. (both side)
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar05.jpg
3. put the bar in place
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar06.jpg
4. here are pic on the driver's side. you can see is very
close to the holes.
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar07.jpg
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar08.jpg
5. the cusco manual says you can un-tight these 2 bolts
to adjust the holes about 3mm away from the tower bar.
(but i couldnt do tat)
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar09.jpg
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar10.jpg
6. so instead move the holes, i put some felt on the holes to
stop they touch each other.
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar11.jpg
7. use your hand to put the bolts back in place (both side)
**push the silver part down and tight the screws again using your
hand until you can't turn the bolts anymore**
then now you can use tools to tight it. remember dun over tight it,
otherwise you will snap the bolt.
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar12.jpg
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar13.jpg
8. NOW tight the screws on the tower bar (both side)
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar13b.jpg
9. the sticker :D
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar15.jpg
here are some of the pic
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar14.jpg
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar16.jpg
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar17.jpg
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar18.jpg
http://members.iinet.net.au/~tommi/ozHonda/TowerBar/TowerBar19.jpg