B18c/b18c7 help

[JDM-derek]

Hey guys before you tell me to search, I've searched already and done my research . Now I just wanna clear things up and any feed back would be awesome

1) Im aware that b18c7 or b18c would fit straight into a EK1 with along side me getting EK4 wiring harness, b18c/c7 ECU, B series shafts and B series linkage. Is this correct?

2) Will my AC Pipe fit on to the B series AC compresser ?

3) Will my Power steering fit hose fit straight on?

4) And last question will i need to run any other new wires from ecu to engine to get it started?

5) fuel pump ? should I get a b series one?



Thanks guys , dont troll please be nice =)

[shepparton]

imo, b18c7 wont fit straight in without Ek b mount.
everything will fit straight in, as long as you use B parts from Ek VTIR

[menacer]

^^ agreed. get all b series EK parts eg. mounts, supports, brackets etc. should make the job much easier..

[Hellomotog]

Use a crv Ac bracket and put the d series compressor on your b18.

[Hellomotog]

Also need an integra ps pump.lines fit fine.

Ecu will need an immobilizer removal. Google it. Whole DIY guide.

Ek4 engine mounts. Except below

99 si civic. Rear bracket
99 si post mount passengers side

Use same tranny mount

[Hellomotog]

Pm me if u get stuck!

[ceekay101]

you mirrin the b series

[dorikin]

yes
no
yes
no
yes

[VTec1987]

1) Im aware that b18c7 or b18c would fit straight into a EK1 with along side me getting EK4 wiring harness, b18c/c7 ECU, B series shafts and B series linkage. Is this correct? YES

2) Will my AC Pipe fit on to the B series AC compresser ? No but you can get CRV b20 AC Bracket and you can use your d series compressor or get EK4 Ac hose to use b series compressor

3) Will my Power steering fit hose fit straight on? Yes, there is 2 types of b series PS pump, 1 for late model and early model

4) And last question will i need to run any other new wires from ecu to engine to get it started? NO

5) fuel pump ? should I get a b series one? Use your stock pump

[Hellomotog]

+ 1 vtec1987

[JDM-derek]

1) Im aware that b18c7 or b18c would fit straight into a EK1 with along side me getting EK4 wiring harness, b18c/c7 ECU, B series shafts and B series linkage. Is this correct? YES

2) Will my AC Pipe fit on to the B series AC compresser ? No but you can get CRV b20 AC Bracket and you can use your d series compressor or get EK4 Ac hose to use b series compressor

3) Will my Power steering fit hose fit straight on? Yes, there is 2 types of b series PS pump, 1 for late model and early model

4) And last question will i need to run any other new wires from ecu to engine to get it started? NO

5) fuel pump ? should I get a b series one? Use your stock pump



ALSO need B series mounts ? and T bracket from which car?

[Hellomotog]

So ek4 mounts.
Rear bracket from 00si civic
Post mount passengers side 00si civic

[FAITHLESS]

Don't need immobilizer bypass if you have the teg ignition barrel and key.

[FAITHLESS]

You need the EK4 T bracket.

[JDM-derek]

Wait can't u use the D series's mounts besides passenger side engine mount and T bracket ?

[EK1.6LCIV]

1) Im aware that b18c7 or b18c would fit straight into a EK1 with along side me getting EK4 wiring harness, b18c/c7 ECU, B series shafts and B series linkage. Is this correct? the shafts and linkage will be correct, however the 1996 itr shafts abs rings will clash on the abs wheel senders, so if you have abs (pretty sure you don't), you'll have to remove the senders on the front.

2) Will my AC Pipe fit on to the B series AC compresser ? use the d16 item with a 1997 crv bracket, have the stock assembly hang in situ whilst you remove the engine

3) Will my Power steering fit hose fit straight on? depends on the pump, on the d16y8 the top attachment is different to the itr pump, I had to cut the brass section and re-use the itr section on my d16y8 line, easy fit with the right metric fittings

5) fuel pump ? should I get a b series one? it'll be fine, I got 600km+ on a trip this weekend and no issues with mine so far

**remember to get the t-post from a 99-00 civic vtir (ITR won't fit)
& the vtir passenger side t post as the itr studs are parrell whereas the civic is offset (I have seen people use the ITR/EG passenger mount and build a custom adaptor, if you can weld and work metal it's an option)

[JDM-derek]

bump to top!

what CV shafts do I use, i thought i could use my stock d series now ppl say i cant =/

[Adamjoeldavis]

You have to use a B series since it has a different thickness of its CV shafts than a D series shafts. I am not too sure but you may need a B series front stud axle too?? Can someone explain this fully cause I am intrested of doing this to my civic too

[JDM-derek]

hey guys can i run B series alternator??

[Winter]

hey guys can i run B series alternator??

beware of obd0, obd1 or obd2 alternators even though they are b series the plugs are different for newer vs older models

[JDM-derek]

beware of obd0, obd1 or obd2 alternators even though they are b series the plugs are different for newer vs older models

i think my plug is different to my harness

http://www.ozhonda.com/forum/showthread.php?170138-wiring-help-for-B-series-!!!&p=3601780#post3601780