PDA

View Full Version : RSB Endlink Upgrade


siir
24-11-2012, 02:48 AM
Hi Guys..

For those who upgraded their rsb to progress, comptech, whiteline, etc.. what end link did u use? how much? where to buy?

I been looking for an end link but could not find any.. I heard moog & ingalls are the best.. Unfortunately the moog & ingalls - when I spoke to the sales rep they say it wont fit right hand drive.. not sure why - I dont want to risk buying it. Went to ebay + other sites and they all say the same thing..

Appreciate your help. Thanks heaps
bennjamin
24-11-2012, 08:32 AM
Avoid whiteline

Try BLOX , ignalls amongst some to research
kryptonite
24-11-2012, 12:40 PM
I bought RSB from Heeltoe with these end links.

THis was last year and ive still not installed the RSB or links.

http://www.fastlineperformance.com/powerlinks-sway-bar-endlinks.html

Im just lazy.....
aaronng
24-11-2012, 02:17 PM
Is this for the CL9? The endlinks for the LHD and RHD models are the same. Both sides are the same length as well. They face a specific direction though, so there are specific left and right side end links.
siir
25-11-2012, 12:54 AM
thx for the info guys..
siir
25-11-2012, 01:04 AM
Is this for the CL9? The endlinks for the LHD and RHD models are the same. Both sides are the same length as well. They face a specific direction though, so there are specific left and right side end links.

yes. its for CL9..
Im abit confused.. or myb im replying at 2.10am half asleep :P
So you're saying it might not fit due to the specific direction/angle = the reason is due to lhd & rhd is different?
Even when u get the specific part (ik90342 & ik90343 = left & right) > will still doesn't fit.

thxx
aaronng
25-11-2012, 01:31 AM
yes. its for CL9..
Im abit confused.. or myb im replying at 2.10am half asleep :P
So you're saying it might not fit due to the specific direction/angle = the reason is due to lhd & rhd is different?
Even when u get the specific part (ik90342 & ik90343 = left & right) > will still doesn't fit.

thxx

No, LHD and RHD models use the same endlinks. There are left side and right side endlinks, which are the two part numbers you listed. If you get one of each, then they will be the correct ones.
Fredoops
25-11-2012, 11:53 AM
Funnily enough I'm looking at those as well.

The Comptech sway bar fooked by rear endlink as well am I've been looking at a replacement. Cause the noise is driving me nuts.

A par of moogs non adjustable endlinks is going I cost almost $100 shipped from the states... Fk that migt as well look at adjustable endlinks in that case.

Would this one work?
http://www.jdmyard.com/index.php?route=product/product&keyword=Endlinks&product_id=609
siir
27-11-2012, 04:21 PM
No, LHD and RHD models use the same endlinks. There are left side and right side endlinks, which are the two part numbers you listed. If you get one of each, then they will be the correct ones.

Thanks Aaronng for your confirmation :)
HuyT
01-12-2012, 03:36 PM
Funnily enough I'm looking at those as well.

The Comptech sway bar fooked by rear endlink as well am I've been looking at a replacement. Cause the noise is driving me nuts.

A par of moogs non adjustable endlinks is going I cost almost $100 shipped from the states... Fk that migt as well look at adjustable endlinks in that case.

Would this one work?
http://www.jdmyard.com/index.php?route=product/product&keyword=Endlinks&product_id=609

What noise is yours making?
Fredoops
01-12-2012, 10:02 PM
What noise is yours making?

knocking when loading the swap bar while turning

had a look underneath today, the the sway bar mount is still intact, and the endlinks dont look straight

so i ended up ordering a part of Moog's Endlinks form Amazon for $60 shipped
HuyT
01-12-2012, 11:24 PM
Yeah the thread of one of my endlinks rotates with the nut when i try to unbolt it. But the knocking noise for me is even over the slightest bump, annoyed as hell.

Could you possibly link us to this endlink on amazon?
Fredoops
01-12-2012, 11:43 PM
Yeah the thread of one of my endlinks rotates with the nut when i try to unbolt it. But the knocking noise for me is even over the slightest bump, annoyed as hell.

Could you possibly link us to this endlink on amazon?


http://www.amazon.com/gp/aw/d/B000C5A0GC/ref=mp_s_a_1?qid=1354369302&sr=8-1&pi=SL75

And

http://www.amazon.com/gp/aw/d/B000C545MM/ref=mp_s_a_1?qid=1354369407&sr=8-2&pi=SL75

Double check the part number so they fit
aaronng
02-12-2012, 09:15 AM
Yeah the thread of one of my endlinks rotates with the nut when i try to unbolt it. But the knocking noise for me is even over the slightest bump, annoyed as hell.

Could you possibly link us to this endlink on amazon?
You remembered to insert a hex key into the middle of the thread part to hold it still while you undo the nut?
siir
03-12-2012, 11:29 PM
knocking when loading the swap bar while turning

had a look underneath today, the the sway bar mount is still intact, and the endlinks dont look straight

so i ended up ordering a part of Moog's Endlinks form Amazon for $60 shipped
wow thats cheap.. I ordered mine at moog website for 90 shipped..
HuyT
04-12-2012, 03:43 PM
You remembered to insert a hex key into the middle of the thread part to hold it still while you undo the nut?

My Hero~
Nuggety Nugget
06-12-2012, 12:14 PM
http://www.amazon.com/gp/aw/d/B000C5A0GC/ref=mp_s_a_1?qid=1354369302&sr=8-1&pi=SL75

And

http://www.amazon.com/gp/aw/d/B000C545MM/ref=mp_s_a_1?qid=1354369407&sr=8-2&pi=SL75

Double check the part number so they fit
OzHonda strikes the wallet again.
Fredoops
06-12-2012, 12:28 PM
You mean fredoops strikes the wallet again lol
Nuggety Nugget
06-12-2012, 03:37 PM
You mean fredoops strikes the wallet again lol
Haha now that I think about it, you are responsible for most if not all of my spendings.
Fredoops
06-12-2012, 06:39 PM
Haha now that I think about it, you are responsible for most if not all of my spendings.

You gonna hate me when I post photos of my flushed PS fluids then... lololol
aaronng
06-12-2012, 11:13 PM
You gonna hate me when I post photos of my flushed PS fluids then... lololol

Do it!!!! :p
Nuggety Nugget
07-12-2012, 12:13 PM
You gonna hate me when I post photos of my flushed PS fluids then... lololol
Lucky for you that doesn't interest me.
Fredoops
11-12-2012, 08:34 AM
Endlinks arrive today from the us of a
Nuggety Nugget
16-12-2012, 10:21 AM
How did you go with the install? I'm a bit confused on what to do with those little screw things.
Fredoops
16-12-2012, 12:53 PM
How did you go with the install? I'm a bit confused on what to do with those little screw things.

we'll find out in a few hours.


EDIT: New endlinks are in.

AWESOME.
Nuggety Nugget
21-12-2012, 09:21 PM
Just changed mine today. It was trickier than what I was expecting. Well worth $60.

http://members.optusnet.com.au/~nhan01/moogs.jpg
Fredoops
22-12-2012, 12:44 AM
Just changed mine today. It was trickier than what I was expecting. Well worth $60.

http://members.optusnet.com.au/~nhan01/moogs.jpg

Yep, it's great, jus make sure your endlinks, swaybar mount etc are greased properly.