Distributor wrecked

[TimmAh85]

hey you guys, my distributor is wrecked and i needs a new one, but i have no idea on how much it will cost me to buy one, i have a standard 92 civic Si i think the engine is a b16a non vtec so if any one knows some prices please tell me.

[bennjamin]

the engine is a d16a8 DOHC non-vtec.
The price for a NEW dizzy , is from $800 - 1200 for a aftermarket or OEM one.
Rebuilding a old dizzy , costs about the $300 mark ( replace igniter , coil + rebuild main bearing).What is your location , as we can guide you in the right direction.

Try to rebuild it first - this is a common problem with our Si - and rebuilding fixes it :) ( been there with my 2 Si's !)

Best of luck.

[TimmAh85]

I am in melb, wheelers hill.
thanks for the advice

[panda[cRx]]

yep very comon d16a8 problem

[flipmods]

Whats up with yours? my one on my Si is throwing a fault code for the CYP and CKP.

[TimmAh85]

ill just be crusing at 2 1/2 grand and all of a sudden it will drop to jsut below 2 grand and i would have to plant my foot to the floor to get it back up again. i took it to the mechanics and they told me it was because of the distributor

[KillerRx4]

Where is recommended in sydney to have a dissy rebuilt?

Ive just come in for pulling the head on my mrs' 88 civic to replace the head gasket. An ordeal in itself (damn shitbox hondas :rolleyes: )

Its been pinging its ring off for quite a while now & has started using coolant & spraying me with it when trying to fill it.

Anyway, I popped the dissy cap off & its almost completely full of oil...a major mess.
There is a fair whack of play, maybe 10-15 degrees in the shaft & some metal part inside under the rotor is loose as buggery. Also found a ball bearing in there & a piece of wire looks sorta like it was once a clip maybe.

Id figured id come here & lok for a 2nd hand dissy, got a rude shock when i see some prices gettin thrown around.
So if anyones got 1 let me know otherwise where to take it for someone to look at it?

Cheers.

[Bowzer]

If your in Sydney try these guys out, they seem to have stock these newly built dizzy's

If your from Melbourne give them a call and see what prices they offer

NARDEK PTY LTD
PO Box 427
FRENCHS FOREST NSW 1640
AUSTRALIA
Phone : +61 2 9984 9984
Fax : +61 2 9984 9988
Email: nardek@nardek.com.au

http://www.nardek.com.au/Distributors.pdf

[Weq]

im sure u could get a MSD setup for around $500.

[crxzzR]

benjammin:
whereabouts in sydney can u get the dizzy rebuilt..
my d16a8 has been giving me a sudden loss of power..most mechanics reckon it's fuel supply related. but rob @ hanny's says its dizzy bearing..
and from what i read here it seems like it happens to a few d's as well

weq: i was lookin @ msd.. any recommendations on which model?

[bennjamin]

benjammin:
whereabouts in sydney can u get the dizzy rebuilt..
my d16a8 has been giving me a sudden loss of power..most mechanics reckon it's fuel supply related. but rob @ hanny's says its dizzy bearing..
and from what i read here it seems like it happens to a few d's as well

weq: i was lookin @ msd.. any recommendations on which model?

I got my last 2 dizzys rebuilt at Hannys by Robert himself. Cost around $300 a pop :( .

[riceball]

hey man, if ur not fussy about the brand etc, u can get one ordered off ebay for around 250 bucks shipped. mine died not long ago and yeah, thats wat i did. does the trick. :D

[aaronng]

OMG, dizzys here are so expensive compared to overseas. AU$100 for a rebuilt one and $300 for a new one.