Chi
07-04-2005, 01:05 PM
Disclaimer: The following is provided as a GUIDE ONLY, and neither myself nor Ozhonda take any responsibility for the outcomes of someone else doing the following. You follow these steps at your own risk!
--------------------------------------------------------------------------
Im not a fan of the rear wiper so have decided to do a DIY to how to remove it, some EG civics motor wipers are held up differently.
One where you can take out the wiper and motor and just place the case+screw back on.
Two, where you take the motor out but you need to buy a plug to hold case into place.
I was stuck with issue 2 so heres how to solve it.
TOOLS NEEDED
- Sink/Drainer plug set ( Can be purchased from Bunnings Warehouse, thanks to EG5 for buying it for me)
- Phillips head screw driver
- 10mm wrench
- 20mm Wrench ( I didnt have one so had to use a adjustable spanner)
http://img476.imageshack.us/img476/9871/wiper24xd.jpg (http://imageshack.us/)
What the wiper looks like before
http://img476.imageshack.us/img476/9078/wiper10zz.jpg (http://imageshack.us/)
Remove the cap cover for the wiper hinge/screw whatever it is on an angle like below.
http://img476.imageshack.us/img476/4112/wiper36wi.jpg (http://imageshack.us/)
Use the 10mm wrench and remove the bolt/nut
http://img476.imageshack.us/img476/2523/wiper41xo.jpg (http://imageshack.us/)
Give the wiper a wriggle and elbow grease to get it out, (WD -40 maybe needed if its too stiff)
http://img476.imageshack.us/img476/6805/wiper51ou.jpg (http://imageshack.us/)
Remove the cap underneath the wiper
http://img476.imageshack.us/img476/8192/wiper69ti.jpg (http://imageshack.us/)
Now on the inside remove the bolts off the cover of the motor with the phillips head screw driver
http://img476.imageshack.us/img476/4338/wiper77fh.jpg (http://imageshack.us/)
Give it a push to the right and pull it out, dun worry it wont snap.
http://img476.imageshack.us/img476/2236/wiper81oi.jpg (http://imageshack.us/)
Remove the three bolts as shown in the pic with the 10mm Wrench.
http://img476.imageshack.us/img476/1972/wiper98mx.jpg (http://imageshack.us/)
Now with a 20mm (not sure was a estimate) or adjustable spanner.
http://img476.imageshack.us/img476/5492/wiper100hl.jpg (http://imageshack.us/)
Make sure you have support for the motor from falling .
http://img476.imageshack.us/img476/1835/wiper125fy.jpg (http://imageshack.us/)
Use the 20mm+ to remove the bolt holding up the wiper motor on the outside as shown below.
http://img476.imageshack.us/img476/9377/wiper111iz.jpg (http://imageshack.us/)
http://img476.imageshack.us/img476/6205/wiper136oo.jpg (http://imageshack.us/)
Remove the following parts show below as not needed, leave the rubber on the window
http://img476.imageshack.us/img476/2303/wiper145ja.jpg (http://imageshack.us/)
Disconnect the 2 power socket/connectors one hooked as support the side of the motor and one to the connector itself.
http://img476.imageshack.us/img476/6118/wiper156yo.jpg (http://imageshack.us/)
http://img476.imageshack.us/img476/6935/wiper166pa.jpg (http://imageshack.us/)
Make sure you keep the plate/hinge thinge supported incase of snapping the other bolt as a precaution.
http://img476.imageshack.us/img476/8836/wiper171qf.jpg (http://imageshack.us/)
Now take the sink plug thing and place it into the hole and the plate on the inside.
http://img476.imageshack.us/img476/5721/wiper189cu.jpg (http://imageshack.us/)
http://img476.imageshack.us/img476/1202/wiper195wf.jpg (http://imageshack.us/)
Take the plate bolt thingie (I dont know what its called) and screw it on the plug.
Apply a bit of force to get it tight inside as it gets a bit hard to turn so jiggle the hinge plate around to it up more.
http://img476.imageshack.us/img476/4153/wiper204sn.jpg (http://imageshack.us/)
http://img476.imageshack.us/img476/65/wiper219po.jpg (http://imageshack.us/)
http://img476.imageshack.us/img476/9657/wiper224lk.jpg (http://imageshack.us/)
Put plastic cover back on and your all done !
http://img476.imageshack.us/img476/4262/wiper237pn.jpg (http://imageshack.us/)
http://img476.imageshack.us/img476/5415/wiper244uf.jpg (http://imageshack.us)
--------------------------------------------------------------------------
Im not a fan of the rear wiper so have decided to do a DIY to how to remove it, some EG civics motor wipers are held up differently.
One where you can take out the wiper and motor and just place the case+screw back on.
Two, where you take the motor out but you need to buy a plug to hold case into place.
I was stuck with issue 2 so heres how to solve it.
TOOLS NEEDED
- Sink/Drainer plug set ( Can be purchased from Bunnings Warehouse, thanks to EG5 for buying it for me)
- Phillips head screw driver
- 10mm wrench
- 20mm Wrench ( I didnt have one so had to use a adjustable spanner)
http://img476.imageshack.us/img476/9871/wiper24xd.jpg (http://imageshack.us/)
What the wiper looks like before
http://img476.imageshack.us/img476/9078/wiper10zz.jpg (http://imageshack.us/)
Remove the cap cover for the wiper hinge/screw whatever it is on an angle like below.
http://img476.imageshack.us/img476/4112/wiper36wi.jpg (http://imageshack.us/)
Use the 10mm wrench and remove the bolt/nut
http://img476.imageshack.us/img476/2523/wiper41xo.jpg (http://imageshack.us/)
Give the wiper a wriggle and elbow grease to get it out, (WD -40 maybe needed if its too stiff)
http://img476.imageshack.us/img476/6805/wiper51ou.jpg (http://imageshack.us/)
Remove the cap underneath the wiper
http://img476.imageshack.us/img476/8192/wiper69ti.jpg (http://imageshack.us/)
Now on the inside remove the bolts off the cover of the motor with the phillips head screw driver
http://img476.imageshack.us/img476/4338/wiper77fh.jpg (http://imageshack.us/)
Give it a push to the right and pull it out, dun worry it wont snap.
http://img476.imageshack.us/img476/2236/wiper81oi.jpg (http://imageshack.us/)
Remove the three bolts as shown in the pic with the 10mm Wrench.
http://img476.imageshack.us/img476/1972/wiper98mx.jpg (http://imageshack.us/)
Now with a 20mm (not sure was a estimate) or adjustable spanner.
http://img476.imageshack.us/img476/5492/wiper100hl.jpg (http://imageshack.us/)
Make sure you have support for the motor from falling .
http://img476.imageshack.us/img476/1835/wiper125fy.jpg (http://imageshack.us/)
Use the 20mm+ to remove the bolt holding up the wiper motor on the outside as shown below.
http://img476.imageshack.us/img476/9377/wiper111iz.jpg (http://imageshack.us/)
http://img476.imageshack.us/img476/6205/wiper136oo.jpg (http://imageshack.us/)
Remove the following parts show below as not needed, leave the rubber on the window
http://img476.imageshack.us/img476/2303/wiper145ja.jpg (http://imageshack.us/)
Disconnect the 2 power socket/connectors one hooked as support the side of the motor and one to the connector itself.
http://img476.imageshack.us/img476/6118/wiper156yo.jpg (http://imageshack.us/)
http://img476.imageshack.us/img476/6935/wiper166pa.jpg (http://imageshack.us/)
Make sure you keep the plate/hinge thinge supported incase of snapping the other bolt as a precaution.
http://img476.imageshack.us/img476/8836/wiper171qf.jpg (http://imageshack.us/)
Now take the sink plug thing and place it into the hole and the plate on the inside.
http://img476.imageshack.us/img476/5721/wiper189cu.jpg (http://imageshack.us/)
http://img476.imageshack.us/img476/1202/wiper195wf.jpg (http://imageshack.us/)
Take the plate bolt thingie (I dont know what its called) and screw it on the plug.
Apply a bit of force to get it tight inside as it gets a bit hard to turn so jiggle the hinge plate around to it up more.
http://img476.imageshack.us/img476/4153/wiper204sn.jpg (http://imageshack.us/)
http://img476.imageshack.us/img476/65/wiper219po.jpg (http://imageshack.us/)
http://img476.imageshack.us/img476/9657/wiper224lk.jpg (http://imageshack.us/)
Put plastic cover back on and your all done !
http://img476.imageshack.us/img476/4262/wiper237pn.jpg (http://imageshack.us/)
http://img476.imageshack.us/img476/5415/wiper244uf.jpg (http://imageshack.us)