DIY gear change & speed light for RSM

[learner]

hi all... was thinking just put 2 led for my RMS... but is gonna be very weird to just have 2 led on the dashboard... so... i bought a little toy car. put the led in as the head & fog light for da toy car...(:D got this idea when i was shopping at coles...:D saw this little nice :honda: civic)


step 1:... drill the holes on da car... i use 3mm led as fog light and 5mm super bright led for the head light. there isnt enough room for the 5mm led... so i have cut the wheel a bit to fit tat..
http://members.iinet.net.au/~tommi/ozHonda/DIY_RSM/001.jpghttp://members.iinet.net.au/~tommi/ozHonda/DIY_RSM/002.jpg

step 2: connect the led with the correct resistor on the (+) side of the led then try to fit it on da car
http://members.iinet.net.au/~tommi/ozHonda/DIY_RSM/003.jpghttp://members.iinet.net.au/~tommi/ozHonda/DIY_RSM/004.jpg

here is da pic after i put everything in...
i only use one (+) wire for all lights in there...
the other 2 wires is connect to the RSM... they are (-)
http://members.iinet.net.au/~tommi/ozHonda/DIY_RSM/005.jpghttp://members.iinet.net.au/~tommi/ozHonda/DIY_RSM/006.jpg

this is the end product... i think it looks ok....
(i will take off the stick tape later... on the side of da car)
http://members.iinet.net.au/~tommi/ozHonda/DIY_RSM/007.jpghttp://members.iinet.net.au/~tommi/ozHonda/DIY_RSM/008.jpg
http://members.iinet.net.au/~tommi/ozHonda/DIY_RSM/009.jpghttp://members.iinet.net.au/~tommi/ozHonda/DIY_RSM/010.jpg

here is how it look like when is operating
http://members.iinet.net.au/~tommi/ozHonda/DIY_RSM/011.jpghttp://members.iinet.net.au/~tommi/ozHonda/DIY_RSM/012.jpg

[Chris_F]

hahaha very imaginitive and cool :thumbsup:

[JDM.Power]

nice! ehehehe

[GenV]

I like it! Very creative!

[FlavzzTEGRA]

looks cool mate, how about your rsm.. u reckon they are worth the dough??

[learner]

looks cool mate, how about your rsm.. u reckon they are worth the dough??

i think is worth it... since u can take it with u when u change your car.
but as u know it doesnt gain any performance... it only show the details....
u will love your car more after installed it... (at least i do)
i was thinking to put the v-tec controller rather then rsm... but the thing is i have no idea about tuning up.. the only way is dyno->change setting->dyno->change setting... therefore i choose the rsm.

[[stealth]]

hahahaha very nice.... looks pretty cool :)

[Q_ball]

very imaginative indeed!!
i rate it :D

[DCLXVI]

hahaha excellent...

[Steer^Gimic]

haha. nice one. clever

[TYPE-ONE]

awesome man. i wonder if ideas will pop up in my head next time i visit coles.

[r`Geno]

Sweet write up!! :thumbup:

[asiansquad]

How would i connect this to a vafc??

which wires do i have to link the led's to??

[dundas]

look on ur VAFC install guide/ instruction manual..
it MIGHT have it on there.. not 100% sure---
does ur VAFC have rev output? if it does.. u can do it-
but yeh.. take a look in ur instruction manual.. this is how mr learner found it---

[Jase EK]

just wondering, for the (-) wat wire did u connect that 2 rsm ? is it the white, for negative trigger ?

[j-specAccord]

bump.. i need some help on installing this ?? anyone help

[dundas]

LOL damn this is old thread.. but anyways .. wat help is needed?
the white wire on the RSM is what you want to connect up and also a power source for the light. (pretty sure :D)
anyways.. seriously Look in your instructions from the RSM and it will show you how towards the back i think. It has been a while...

[panda[cRx]]

whoa only just noticed this thread now.... velli kewl :D

[aStRooo]

connect it to the white wire from the RSM for ground (thats the switching ground) and splice into the RSM or the ECU's power

[dundas]

u can really go to any power source... so what ever you can get your wires on. give it a test and see if it works... (set rev @ lowest) rev to that particular point and your light should work :)

[connorling]

just a question, which wires do u connect to the light?