B16A header on B18C

[civic_mods]

Can Aftermarket B16A civic EG header fit to B18C Integra DC2R?
I do search before i post,but can't really found a good answer at all!!
:(

[BananaBoat]

B16A block is shorter than B18C.

You will have problems clearing the B18C block.

[civic_mods]

Thanks mate!
it mean it can't be fitted without problems..........LOL

[[[d a n n y]]]

pretty sure..
it wont fit.
it'll bolt up
but the length isnt long enuff due to the taller block of the B18c

[civic_mods]

but will it touch the oil sump or other stuff?
how abt make the cat piping a bit longer to let it fit?
possible?

[tRipitaka]

but will it touch the oil sump or other stuff?
how abt make the cat piping a bit longer to let it fit?
possible?
do you mean modify the header ? make it longer/taller ?

[civic_mods]

i mean make the piping of the cat longer

[pornstar]

civic mods, most companys that make headers make them for both b16a and b18c as the one unit, so as is often the case, the header is made longer already to clear the b18c and b16a sumps. Best bet would to actually take a look and see if it is physically the same length as the b18c unit.

[Dxs]

well for reference my 5zigen b16a ef8 specific header has a 1cm if not less clearance from the sump with the b16a engine. So you would have almost no room to play with

[BlitZ]

I've got a set of JDM bling - Jasma approved stuff...

stamp badging says for b16a....

..

tried it on mates b18c2.. worked fine ...

All depends on the make..
...................................

Alot of the 4-2-1 stuff is generic as they arent really worried about it hanging abit lower on the b16a... the 4-1 is more specific more of the times as they hang too low already...

[dc2rrrr]

Trail and error. I imagine the flange to the cat will need to be changed as they are all different from jap spec to ozzy spec to us spec
Good luck

[panda[cRx]]

civic mods, most companys that make headers make them for both b16a and b18c as the one unit, so as is often the case, the header is made longer already to clear the b18c and b16a sumps. Best bet would to actually take a look and see if it is physically the same length as the b18c unit.


Trial and error. :thumbsup::thumbsup::thumbsup:

as others stated it depends on the make, but in many cases it will work fine

[VT3C]

I've got a set of JDM bling - Jasma approved stuff...
stamp badging says for b16a...

Yeah I just bought a TANABE 4-2-1 off Kris (ozhonda member) and this header is specific to B16A (serial number: 93E023 - B16A) however the previous owner (Kris) apparently had it on his B18C but it was physically touching his sump - thought there are no visible scratches on the header where this would have happened. the clearance on my B16A is very tight - maybe 1cm - so it might fit on your B18C but wont be the best.

Blitz - do you have pic of your header ? mine was labeled only as 'JASMA' and the serial number and I emailed JASMA and they traced the serial number back to TANABE.

when i searched for both Tanabe 4-2-1 and/or the serial number on google I came up with only ONE reference.. so I am trying to find out more info on these headers etc.

cause yeah 'JASMA' is not a brand.. it's an accreditation from an organisation.

[civic_mods]

Thanks guy for the answer
but i asume that if it is too close to the sump,or may be 1 cm for clearance.
it just like boing water in the kitchen for your engine oil temp???

[HONDARA]

hello guys. I have an integra db8 with b18c engine and i put the same jasma heaters (93Eo23) on it. There is no problem at all, it fits like the stock ones.
I have thow another problem and i need some help. I need the gasket wich is be2in the heaters and the second part coz its blowing from there. Is anyone
know where can i find one? thanks

[vinnY]

b16 specific headers won't fit b18's
headers made for 'b series' generally will fit both
jasma's more of a specification than brand fyi

as for your problem, best bet is to get it to an exhaust shop and see whether they have a replacement

[geeang]

hello guys. I have an integra db8 with b18c engine and i put the same jasma heaters (93Eo23) on it. There is no problem at all, it fits like the stock ones.
I have thow another problem and i need some help. I need the gasket wich is be2in the heaters and the second part coz its blowing from there. Is anyone
know where can i find one? thanks

Just so you guys know - as vinnY said JASMA isn't a brand, it's a classification - something like the stamped approval for the emissions-equivalent in Japan.
My Mugen twinloop is JASMA approved (and has the stamp).

You can get new OEM header gaskets from JDMyard (an Ozhonda trader), or you can take it to any exhaust shop and they would be able to help you with the problem.