EG Carbon Fibre Bezel

[NightKids]

Hey guys i tried to install this today:-

http://img150.imageshack.us/img150/8091/ae1bhk7.jpg

I pulled out my dash & everything but how do I get the plastic thing off? It seems to be glued, does that mean I have to snap it out? Thanks in advance guys...

[Lukezen27]

Bump for the answer to as I have to replace the cracked plastic thing on mine..

LukeZen

[Captiva_Blue]

I would suggest getting a low temp heat gun or a hairdryer and applying the heat to the glued edge, the glue should go tacky fairly quickly, then you can pull the cover away. Make sure you test the heat first on an area that won't be really visible just in case the heat makes the plastic go cloudy. Just a suggestion, I haven't done this before on a dash but I've done a similar thing with plastic lens headlights and I had no troubles...

[marte]

you don't need to do use any heat guns etc. the plastic bit should come off. I tooko the thing off to put on my luminious glow dials recently.

[NightKids]

It doesn't really come off because it's like glued together... if you were to take it off you'll have to snap it off. But then how do you put it together again?

[Boban]

I used a heat gun on low temp. as Captiva Blue had and pulled it off carefully. I painted mine white. And than just re-glue it back in place. Marte, your dials sit underneath the plastic that NightKids is talking about. That comes off the cluster because it's held in by clips or something, i pulled that off too when i did my indiglows. But yeah, just be very carefull whed you do it man, it's not hard

http://img145.imageshack.us/img145/9562/2411051729ly9.th.jpg (http://img145.imageshack.us/my.php?image=2411051729ly9.jpg)

[marte]

wait which plastic thing are we taklin about now :O

[NightKids]

The plastic that you see when you look straight into the dials.

[ToFuBoi]

get your mums/sisters hair dryer out.. heat up one spot for a while and slide in a thin peice of metal or something and jimmy it around and move along..

btw i was guna buy one of those too.. they look sick!

[ToFuBoi]

if u give up i shotgun buying it off ya :)

[NightKids]

How would i stick the plastic bit back on though? What glue would i use?
Yeah if it gets a bit too hard, i'll consider selling it...

[ToFuBoi]

probly go down to the hardware store ask for some clear drying stuff i guess for plastics? otherwise superduperglue!!

[ToFuBoi]

also wanted to add u better make it air tight just in case one cold cold morning u come out and its all fogged up inside n that :( wont be good
but i dont see it happening really

[destrukshn]

sounds odd.. i've pulled apart about 8 honda clusters 4 being EG clusters, and never ones i had a problem taking em out, let alone having to deal with glue.
should just be clipped on, and that's it.

[ToFuBoi]

yeh thats what happend with mine.. just a few of those metal clips.. but was playing with a friends one was held together buy a bit of glue *shrugs*

[Boban]

My one was glued, but on another car (nissan) when i pulled it appart it was just plastic clips. I used just the good old superglue u get from anywhere, $2 at the discount store and it's working fine, no fogging up or anything. And also, the edges are hidden away behind the black plastic that has the a/c vents in it so if you mess it up a bit (like i did), noone can see it.

Where r u located by the way NightKids, if you are here in brisbane i can give you a hand

[NightKids]

yeah me & my friend thought it was help together by clips as well, but then we tried yanking it off & keep hearing this crackling noise, that's when we noticed that it was actually glued together. Maybe only the newer model EG's are glued? Cause mine is 95.

Thx for the offer Boban but i'm from Melb, that's very kind of you... cheers mate

[TYPE-ONE]

ive just bort the same one you have. how long did it take to receive

[NightKids]

did u get it off eBay? cause it took about a week a half for me

[TYPE-ONE]

cool mine shud be here soon then

[Lukezen27]

I used a heat gun on low temp. as Captiva Blue had and pulled it off carefully. I painted mine white. And than just re-glue it back in place. Marte, your dials sit underneath the plastic that NightKids is talking about. That comes off the cluster because it's held in by clips or something, i pulled that off too when i did my indiglows. But yeah, just be very carefull whed you do it man, it's not hard

http://img145.imageshack.us/img145/9562/2411051729ly9.th.jpg (http://img145.imageshack.us/my.php?image=2411051729ly9.jpg)

Hay guys

I can't work out how to remove the black plastic thing that holds it all into place

HELP ASAP

It’s the bit with the clock and vents

Thanks heaps

Luke

[TYPE-ONE]

theres a screw near the clock. make sure thats out

[Lukezen27]

theres a screw near the clock. make sure thats out

Yeah I got that one

One behind the clock and two above the dials

where's the rest?

this driving me made lol

[TYPE-ONE]

thats all there is
now u have to yank it out
carefully.

[Lukezen27]

thats all there is
now u have to yank it out
carefully.

Thanks bro

Yeah I found that out!!! dam I had to yank so hard I was sure I was going to break something :eek:

Next problem...


yeah me & my friend thought it was help together by clips as well, but then we tried yanking it off & keep hearing this crackling noise, that's when we noticed that it was actually glued together. Maybe only the newer model EG's are glued? Cause mine is 95.

Thx for the offer Boban but i'm from Melb, that's very kind of you... cheers mate

Did you end out getting it off bro?

I now need to do the exact same thing and she's glued for sure...

[NightKids]

seems like the only solution is to use a hair dryer, but i haven't actually tried it yet.

[Lukezen27]

seems like the only solution is to use a hair dryer, but i haven't actually tried it yet.

tried that.. doesn’t work:o

Some parts look to be heat pressed :thumbdwn:

I'd like to see pics of someone who was able to get it off without damage!!

I know there's no way I can, I've busted one already grrr

[Boban]

I used a heat gun (guess that was higher temp than the hair dryer - has 300c and 500c setting :p) to get mine off. I did it in sections mate, starting from one corner and work slowly along the top off it and so on. Maybe try and put something like toothpick in between the areas you unglued already so they don't stick back togrther coz the glue will be hot.... dunno what else to say appart from....nah that's all i got :D

[TYPE-ONE]

Mine arrived yesterday. Looks Sick. Now to put it in. Should be no problems

[NightKids]

Let us know how you go & preferably a DIY would be great!

[TYPE-ONE]

Installed it already. Basically just used a hairdryer to heat it up slightly then used very thin flathead screwdriver to split apart. Focus on one side first. Then heat up other parts slowly and use stanley knife to precisely split the plastic apart. In around 10-15 mins should be all off.

Bezel fits very nicely. Great product.

[Boban]

Got pics Type One, mine's looking kinda boring with white bezel and now white indiglows :(, wanna change it to something else

[TYPE-ONE]

Pic will come soon. Once ive wired everything up. Im converting the dash lights to LED also to give the cluster a full EK9 theme.

[NightKids]

Yeah i got blue LED's with mine, but unfortunately one indicator one isn't working atm.

[Boban]

I HAD blue led's in mine b4 i bought the indiglows. They were little push in blade light bulbs like you use in parkers up the front, but smaller (5mm from memory) but i kept blowing them up for some reason. I have my alarm connected so the taillights/parkers flash instead of the indicators, maybe that's why they kept blowing up. Anyhow, at $15/pair it worked out chaper for me to get some blue indiglows :p

[TYPE-ONE]

i got everything installed. pics up tm. doesnt look like ek9 style at nite. the lgihts are very red. looks more like cl7 Euro-R style dash

[TYPE-ONE]

Some pics
http://i8.photobucket.com/albums/a26/TYPE-ONE/EK9Wannabe6.jpg
http://i8.photobucket.com/albums/a26/TYPE-ONE/EK9Wannabe5.jpg

[NightKids]

Oh man that looks so hot. What bulbs did you use to get that colour?

[TYPE-ONE]

Um instead of the original 1 filament type bulb . i put in 3 red led into each hole. wired them all up and there you have it. i recommend getting amber led if you want ek9 style. Mine is like full on red like audis and euro sport.

[Boban]

Looks good man