View Full Version : b16a head on a b20 bottom end NEED HELP ASAP
vtec+turbo
20-10-2006, 02:45 PM
hi all i have just taken the turbo kit off my car and now want to put a b20 bottom end in with my b16a head
i have tried the search button but nothing came up
The question is.. What do i need
b20 bottom end
b16a head
golden eagle vtec conversion kit????
*
*
*
where do i get these items from?? i already have the head
what else will i need
I will be very greatful for peoples educated responces
TECBOY
20-10-2006, 02:48 PM
pm the user FLY he's a top bloke with this conversion i think
he'll help ya for sure
look on honda-tech for everything u need
SKREMN
20-10-2006, 04:33 PM
if your going to boost your b20 i would recomend sleaving the block
i got mine done with darton sleaves it will handel up to 30psi
this block will be for sale soon
but since you took off your turbo i'm guessing your not going to boost the b20?
BlitZ
20-10-2006, 04:45 PM
yesh.. as above...
....
shopping parts needed:
b20 bottom end
b16a head
golden eagle vtec conversion kit (should contain plug, dowels, head gasket)
b18c Waterpump and timing belt
ARP rod and head bolts
A few beers
in addditional to all the other std stuff..
rear main seal.. you will have no PCV.. etc etc..
Best person to ask is Tinkerbell :thumbsup:... budget b20 expert
turtleEK1
20-10-2006, 04:50 PM
do a search through this site... would be something wrong if they didn't have anything on it...
http://www.b20vtec.com
Stoosh
20-10-2006, 05:58 PM
http://www.ozhonda.com/forum/showthread.php?t=54078
hi all i have just taken the turbo kit off my car and now want to put a b20 bottom end in with my b16a head
i have tried the search button but nothing came up
The question is.. What do i need
b20 bottom end
b16a head
golden eagle vtec conversion kit????
*
*
*
where do i get these items from?? i already have the head
what else will i need
I will be very greatful for peoples educated responces
jdmyard
& ebay.com are the 2places i'd buy a golden eagle kit from.
as to what else you will need, then blitz has covered it above
Mugen_B16B
01-11-2006, 01:48 AM
can u use a b18c2 head for this conversion??
SKREMN
01-11-2006, 06:15 PM
yes you can
any b series head can be used
string
01-11-2006, 07:41 PM
But make sure you get the right intake manifold for the head.
I.e. the B18A manifold won't fit on any VTEC head. The B16/ITR manifold won't fit on Vti-R head and vice-versa.
You will also need either a VTEC distributor, or you will have to chop off one leg from your non-VTEC distributor (like I did), and just have it attached by the single top bolt.
ACTI0NMAN-1
01-11-2006, 09:17 PM
b20 bottom end -wrecker or ozhonda member
b16a head - ozhonda for sale thread.
Golden eagle vtec conversion kit - ozhonda trader
ARP rod bolts - Ebay US
TypeR Valve springs - Ozhonda Trader
TypeR oil & water pump - Ozhonda Trader
New B series bearings - Search Ebay US for a complete bottom end kit
Belts - Ozhonda Trader
Thermostat - Ozhonda Trader
Radiator Hose extension - Local Car Part Supplier
Vtec Solenoid/Vtec Distributor -
ECU dohc vtec (obdo or obd1) -
o2 sensor -
Golden Eagle/ARP headstuds
Pistons w/ Rings - Ebay US
Throttle Cable/Throttle Body/Intake Manifold
(Snail with 2nd Butterflys/ITR/Skunk2)
string
01-11-2006, 09:25 PM
Ah yes the above posts brings up an often overlooked item, the upper radiator hose. The vtec heads have the coolant outlet on the intake side, rather than the exhaust side causing the non-vtec upper hose to be a little too short, and not the right shape.
Since I forgot to take this hose from the halfcut I ripped the head out of, I used a spare lower hose I had and hacked it up until it fit. A better option is obviously to buy a new one :)
ACTI0NMAN-1
01-11-2006, 09:31 PM
i forgot about the head studs. so i've edited the post.
you also have to extend a few wires, like the map sensor and possiby a 4 wire o2.
Powered by vBulletin® Version 4.2.2 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.