View Full Version : what extractors are these?
XB-16-AX
26-03-2007, 10:09 PM
hi..
some people are saying that:
JDM ITR OEM extractors are 4-1 and stainless &
AUDM ITR OEM extractors are 4-2-1 and are cast iron.
But the below pic i have is an 4-2-1 OEM from a ITR ..but is it JDM or AUDM as they are stainless as well..
its weird coz some mechanics are saying they are JDM and others are saying they are VTiR ...weird....and these are well known performance mechanics too.
anyone can shed some light here for an accurate confirmation?
they are either AUDM ITR ot 96-97 Spec JDM ITR
ekhybrid
26-03-2007, 11:11 PM
yes i say AUDM too
TODA AU
26-03-2007, 11:27 PM
Ditto...
XB-16-AX
26-03-2007, 11:35 PM
wy do others say its a B16A OEM ...and others say AUDM ITR OEM is cast iron ???
weird ...
so who is going to confirm this 101% :p
jdmTYPE R
27-03-2007, 12:12 AM
Audm....
BlitZ
27-03-2007, 09:33 AM
AUDM 100%
they arent even 4-1 to be JDM ITR
aaronng
27-03-2007, 09:53 AM
They look cast iron to me.
XB-16-AX
27-03-2007, 10:39 AM
good stuff guys!!
thanks for all your confirmation!!
i guess its time for an upgrade to something better!!! =)
BlitZ
27-03-2007, 11:00 AM
They look cast iron to me.
isnt cast iron ore the lump of lava on most std OEM manifolds.. :(... the ITR looks to be mild steel
Limbo
27-03-2007, 11:33 AM
the b16A look like stainless steel also, they don't look cast, i've got a set sitting at home, Most of the 4-2-1 from Honda look very similar. The best way to tell is there is usually some markings on the factory headers, but i dunno what means what
bennjamin
27-03-2007, 01:19 PM
this is the OEM AUDM ITR header - mild steel 4-2 section.
The stock b16a2 header is single piece cast
This header ( 4-2 section) is the same as off a JDM SiR DC2 too
aaronng
27-03-2007, 01:55 PM
the b16A look like stainless steel also, they don't look cast, i've got a set sitting at home, Most of the 4-2-1 from Honda look very similar. The best way to tell is there is usually some markings on the factory headers, but i dunno what means what
Stainless wouldn't have that much corrosion. It still might look brown, but when you run your hand over it, it still feels smooth-ish.
XB-16-AX
27-03-2007, 05:01 PM
this is the OEM AUDM ITR header - mild steel 4-2 section.
The stock b16a2 header is single piece cast
This header ( 4-2 section) is the same as off a JDM SiR DC2 too
CORRECT -
this extractors i have is 4 pipes then into 2 down pipe then into collector.
the only reason why its brown rusty look is because it has been rained on before it was fitted and was sitting in the shed for a while.
but if u touch it ...its smooth as a babys bottom!! :p
Plus when i had the old B16A top header it was definately cast iron and wasnt even shaped like the one on the pic ..it was gay! :thumbdwn:
thats why i replaced them!!!
bennjamin
28-03-2007, 09:38 AM
yes - most metal will get SURFACE rust giving
giving it a "cast iron" appearance. BTW this 4-2 section of the header , is so obviously NOT cast iron. IT is individual primary pipes and they are welded at the 2-1 upper section
XB-16-AX
28-03-2007, 11:15 AM
yes - most metal will get SURFACE rust giving
giving it a "cast iron" appearance. BTW this 4-2 section of the header , is so obviously NOT cast iron. IT is individual primary pipes and they are welded at the 2-1 upper section
Kools..
GUys look at the atatchment - THESE ARE EXAMPLES OF CAST IRON EXHAUST MANIFOLDS and verrryyy big difference to the one im talking about.
So Ben - what do u think is the final Verdict on what are these extractors came from?
jdmTYPE R
29-03-2007, 08:39 PM
pic 1 looks like b16a
pic 2 and 3 looks like from a single cam...
XB-16-AX
29-03-2007, 09:38 PM
pic 1 looks like b16a
pic 2 and 3 looks like from a single cam...
correct - but guess what they are CAST IRONS heheheh
bennjamin
29-03-2007, 09:41 PM
correct - but guess what they are CAST IRONS heheheh
yeah we know duh lol. Its obvious they are - single piece cast iron.
And the one you posted earlier is a single piece mild steel welded item - off a AUDM dc2 ITR or a JDM SIR.
XB-16-AX
29-03-2007, 10:11 PM
yeah we know duh lol. Its obvious they are - single piece cast iron.
And the one you posted earlier is a single piece mild steel welded item - off a AUDM dc2 ITR or a JDM SIR.
sweet..
just making sure that "other" people know the differences between cast iron headers and the one from my original post@@
thanks guys !!
this can now be closed.
bennjamin
01-04-2007, 01:50 AM
sweet..
just making sure that "other" people know the differences between cast iron headers and the one from my original post@@
thanks guys !!
this can now be closed.
good thoughts.
Cheers fr the insight Closed
Powered by vBulletin® Version 4.2.2 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.