DA9 help intstalling sports air filter kit

[KLA80T]

i bought a sports air filter set from ebay and there is two small tubes going to the pgm fuel injection system tingy... but there is 3 tubes from the stock, what should i do? where should i plug which? help please!!!!!

[lilwilliam]

i bought a sports air filter set from ebay and there is two small tubes going to the pgm fuel injection system tingy... but there is 3 tubes from the stock, what should i do? where should i plug which? help please!!!!!

theres a t plug that plugs rite into that, which will sove ur probs shouldnt cost much aorund 5 bucks or so from ur nearest auto store.
regards william

[KLA80T]

thanks for the quick reply.....

like a Y connector to put the two skinny one together? will it do anything bad/damage to the car sensor or something? the kit is already placed... can i drive it atleast to the shop to buy that connector? or should i put the stock back till i can get that connector? help...

thanks.

[IZY-10]

just connect the two lines. the fat one and one skinny one. the pipe that comes off the top of the manifold you dont need to connect as this device only slows down your deceleration between gears. I took mine right off so that i can use my strut brasing

[KLA80T]

thanks guyz!

[FR33K]

true.. i dont have any of those pipings either... all removed except the one breather pipe from the rocker cover to the intake

[tseesinngwailo]

Any pikkys of the install? would help, I think I only have 2 on mine

[FR33K]

if you look at my before and after you can see which one you need (yellow in after).. the other 2 come from the 2 dash pots on the Intake manifold... i have mine removed in the 2nd pic but u cant see cos of the strut bar.. but like everyone said.. you will need to buy a connector shaped like a 'Y' to hook them up.

http://img.photobucket.com/albums/v110/FR33K/pic5.jpg



http://img.photobucket.com/albums/v110/FR33K/pic7.jpg

[destrukshn]

nice!!

[KLA80T]

nice pics fr33k! so, My pipe has two pipe out... the big one and the skinny one....based on your pics (the stock pic) the big one goes to the big hose but cwhich of the skinny hose should i plug? the one on the left or the right hand side? which is more important to plug in?

[KLA80T]

can i also ask you guyz where the two metal piece that comes in the kit go? the straight long one with 3 hole and the small right angled one with one hole? sorry for asking stupid questions, i just want to do this right? hehehe

[FR33K]

nice pics fr33k! so, My pipe has two pipe out... the big one and the skinny one....based on your pics (the stock pic) the big one goes to the big hose but cwhich of the skinny hose should i plug? the one on the left or the right hand side? which is more important to plug in?

thats right... the big hose has to go to the breather cover.. the 2 smaller hoses coming from the intake manifold have to be connected together using a 'Y' connector to join into the one connection in the new intake pipe.. if that makes sense

[KLA80T]

i finally finished my project yey!!! thanks guyz!
i will probably have to change all the tubing aswel....

http://i12.photobucket.com/albums/a207/kla80t/DSC00656.jpg

[wkdteg]

just a different point of view
i had the same prob when installin my simota intake on my old car. went down 2 the shops n bought a breather filter for rocker cover which ment i didnt need that 3rd outlet from the piping... anywyas heres sum pics...

http://i68.photobucket.com/albums/i5/rami_g86/wkdteg%20mk1/IMAG0007.jpg

close up
http://i68.photobucket.com/albums/i5/rami_g86/wkdteg%20mk1/IMAG0009.jpg

KLA80T... not sure if u were supposed 2 connect the rocker breather hose 2 the throttle body

[KLA80T]

i followed fr33ks set up... i think eigther way is fine as long as the air goes in... i was about to get a breather but it looks like that it will only get hot air from the engine bay as suppose to the cooler air coming direct from the intake.... i think? correct me if i'm wrong...