czy_sol87
18-05-2007, 01:42 PM
Disclaimer: The following is provided as a GUIDE ONLY, and neither myself nor Ozhonda take any responsibility for the outcomes of someone else doing the following. You follow these steps at your own risk!
tools u might need for the install
-dremel, or other electric cutting device
-socket set or spanner set(not sure what sizes, but probly 10 or 12)
-a friend (highly recomended, u'll need the help to force the lip on)
-etc (cant really remember what else i used:p)
Step 1: take off ur bumper, trust me it will be heaps easier to do this if u can move the lip around the bumper easierly
Step 2: then lay out the lip and put it against ur bumper, and note where u have to cut.
there is a grove for where a lip would go if the delsol had one from factory
cut the lip so it fits into the grove, like so
http://i29.photobucket.com/albums/c276/czy_sol87/DSC00447.jpg
Step 3: there are 2 peices of plastic protruding from the lip thats surpost to bolt to the bumper
however these are no use on the delsol cause they are just in the way, so cut them off
here are some pics of roughly where they were
http://i29.photobucket.com/albums/c276/czy_sol87/DSC00451.jpg
http://i29.photobucket.com/albums/c276/czy_sol87/DSC00448.jpg
Step 4: remember to always trial fit it before u cut, and always cut off a little bit at a time
the last thing u want is to cut something that u werent surpost to and stuff up the lip
the outside of the lip should line up with where the paint stops on the bumper
http://i29.photobucket.com/albums/c276/czy_sol87/DSC00454.jpg
http://i29.photobucket.com/albums/c276/czy_sol87/DSC00453.jpg
^^see doesnt fit exactly, but oh well u cant have everything:D
http://i29.photobucket.com/albums/c276/czy_sol87/DSC00452.jpg
the dremel is what u would use for most of the cutting and "sanding"
dont worry about what the sectons u cut looks like, all the bits u cut or sanded should be in areas where its unnoticeable once on the car
Disclaimer: The following is provided as a GUIDE ONLY, and neither myself nor Ozhonda take any responsibility for the outcomes of someone else doing the following. You follow these steps at your own risk!
hey guys just thought i would put this into a DIY for those that want a lip on their gen3 crx/delsols
Step 5: once everthing is cut to shape and fits, start using the bolts provided and bolt everything together starting from the middle and working ur way around. this is where a friend will come in handy, either get them to hold the lip while u screw or get them to screw and u Force the lip on
remember that the eg6 lip wasnt made for the delsol, so there will be some forcing and such to get it on
also u might need to use other screws so the lip looks flush
this is what the ends look like on my car
http://i29.photobucket.com/albums/c276/czy_sol87/DSC00445.jpg
and this is what it should look like once on:D
http://i29.photobucket.com/albums/c276/czy_sol87/DSC00401.jpg
damn!! thats slammed:eek:
Wynode edit: Added disclaimer
tools u might need for the install
-dremel, or other electric cutting device
-socket set or spanner set(not sure what sizes, but probly 10 or 12)
-a friend (highly recomended, u'll need the help to force the lip on)
-etc (cant really remember what else i used:p)
Step 1: take off ur bumper, trust me it will be heaps easier to do this if u can move the lip around the bumper easierly
Step 2: then lay out the lip and put it against ur bumper, and note where u have to cut.
there is a grove for where a lip would go if the delsol had one from factory
cut the lip so it fits into the grove, like so
http://i29.photobucket.com/albums/c276/czy_sol87/DSC00447.jpg
Step 3: there are 2 peices of plastic protruding from the lip thats surpost to bolt to the bumper
however these are no use on the delsol cause they are just in the way, so cut them off
here are some pics of roughly where they were
http://i29.photobucket.com/albums/c276/czy_sol87/DSC00451.jpg
http://i29.photobucket.com/albums/c276/czy_sol87/DSC00448.jpg
Step 4: remember to always trial fit it before u cut, and always cut off a little bit at a time
the last thing u want is to cut something that u werent surpost to and stuff up the lip
the outside of the lip should line up with where the paint stops on the bumper
http://i29.photobucket.com/albums/c276/czy_sol87/DSC00454.jpg
http://i29.photobucket.com/albums/c276/czy_sol87/DSC00453.jpg
^^see doesnt fit exactly, but oh well u cant have everything:D
http://i29.photobucket.com/albums/c276/czy_sol87/DSC00452.jpg
the dremel is what u would use for most of the cutting and "sanding"
dont worry about what the sectons u cut looks like, all the bits u cut or sanded should be in areas where its unnoticeable once on the car
Disclaimer: The following is provided as a GUIDE ONLY, and neither myself nor Ozhonda take any responsibility for the outcomes of someone else doing the following. You follow these steps at your own risk!
hey guys just thought i would put this into a DIY for those that want a lip on their gen3 crx/delsols
Step 5: once everthing is cut to shape and fits, start using the bolts provided and bolt everything together starting from the middle and working ur way around. this is where a friend will come in handy, either get them to hold the lip while u screw or get them to screw and u Force the lip on
remember that the eg6 lip wasnt made for the delsol, so there will be some forcing and such to get it on
also u might need to use other screws so the lip looks flush
this is what the ends look like on my car
http://i29.photobucket.com/albums/c276/czy_sol87/DSC00445.jpg
and this is what it should look like once on:D
http://i29.photobucket.com/albums/c276/czy_sol87/DSC00401.jpg
damn!! thats slammed:eek:
Wynode edit: Added disclaimer