EK front lip hardware- where to get?

[Ry_]

Hi all,

Wondering if anyone knows where to get the following:
http://www.inlinefour.com/oemhofrlipha.html

http://us.st11.yimg.com/us.st.yimg.com/I/twincamtech_1958_69185356

The site only sends to the US and CA..

would Bunnings have anything similar?

Cheers and thanks again.

[Zdster]

Honda, but if you are installing an aftermarket lip just get some double sided tape and some screws and washers from a local hardware store and that will do the job just as well.

[Sydsyd]

yay mikey!!!

long time no spam mikey...

yeah, hardware store is the go:D

[Ry_]

Got the lip from Honda... OEM with no hardware. Long story here:
http://ozhonda.com/forum/showthread.php?t=72113

I've been researching and so far it looks like I may be able to get the job done with 'clip nuts' or 'spring nuts' from Bunnings. Might see if I can pick up some 'cashew nuts' too lol.

'Going nuts'.

[Zdster]

Got the lip from Honda... OEM with no hardware. Long story here:
http://ozhonda.com/forum/showthread.php?t=72113

I've been researching and so far it looks like I may be able to get the job done with 'clip nuts' or 'spring nuts' from Bunnings. Might see if I can pick up some 'cashew nuts' too lol.

'Going nuts'.

You really dont need to get those little 'u' brackets. Just screw the lip to the bumper and use double sided tape. It will hold just as well and wont cost a fortune.

P.S. Hi Syd

[Ry_]

Just checking- doublesided tape as a buffer between the edge of the bolt and the plastic, or doublesided tape to line the edge of the bumper?

[Zdster]

Just checking- doublesided tape as a buffer between the edge of the bolt and the plastic, or doublesided tape to line the edge of the bumper?

No, put a screw in each fender well (through the lip) and use a couple of screws across the bottom front of the fender/lip and wherever there isnt a screw use double sided tape (basically as a backup). Send me a PM if you need help/assistance.

[STTICH]

where to?

if not Honda , then Bunnings ! :)

[Ry_]

Thanks guys! I just got a bunch of bolts, nuts and washers from Bunnings. Zdster, thanks for the offer. Currently wondering about the placement of bolts, but I suspect when it comes time to install it it'll be more obvious. Will definitely PM you if I get stumped.

Also, will post pictures of the bolts used should they work, so that the next guy has it a bit easier!

[Zdster]

Thanks guys! I just got a bunch of bolts, nuts and washers from Bunnings. Zdster, thanks for the offer. Currently wondering about the placement of bolts, but I suspect when it comes time to install it it'll be more obvious. Will definitely PM you if I get stumped.

Also, will post pictures of the bolts used should they work, so that the next guy has it a bit easier!

Follow the fitment guide for the stock screws if that makes life easier. There really isnt any science to it, but send me a PM if you need anything.

[Ry_]

Didn't get a fitment guide with the front lip. Got one for the rear lip though.

[Zdster]

Didn't get a fitment guide with the front lip. Got one for the rear lip though.

See link: http://www.hondaautomotiveparts.com/instal/aii/pages/civic/1998/19150_01.html

[Ry_]

Thanks for the link.. turns out this one is for 99-00 though:
http://www.hondaautomotiveparts.com/instal/aii/pages/civic/1999/19811_01.html

Bookmarked!

ps. Darn. Need to go back to Bunnings to get self tapping screws! *mumble*