xdannyx
17-10-2007, 09:40 PM
Disclaimer: The following is provided as a GUIDE ONLY, and neither myself nor Ozhonda take any responsibility for the outcomes of someone else doing the following. You follow these steps at your own risk!
Aim: remove rear seats, pretty simple.
Required: 10 mm spanner (a 10 mm socket will make it easier though)
Steps:
1. undo velcro from boot lining.
http://i11.photobucket.com/albums/a196/endlessxdespair/car/100_7611.jpg
2. undo bolts on right side seat.
http://i11.photobucket.com/albums/a196/endlessxdespair/car/100_7612.jpg
http://i11.photobucket.com/albums/a196/endlessxdespair/car/100_7613.jpg
3. push seat forward and lift out.
http://i11.photobucket.com/albums/a196/endlessxdespair/car/100_7614.jpg
4. undo bolts on left side seat.
http://i11.photobucket.com/albums/a196/endlessxdespair/car/100_7616.jpg
http://i11.photobucket.com/albums/a196/endlessxdespair/car/100_7619.jpg
5. angle seat as shown then push to the left.
http://i11.photobucket.com/albums/a196/endlessxdespair/car/100_7620.jpg
6. there will be one bolt holding down the bottom part of the seat, undo this and lift/wiggle seat until it pops out.
http://i11.photobucket.com/albums/a196/endlessxdespair/car/100_7622.jpg
http://i11.photobucket.com/albums/a196/endlessxdespair/car/100_7625.jpg
7. once you have removed the boot lining and space saver it will look like this.
http://i11.photobucket.com/albums/a196/endlessxdespair/car/100_7630.jpg
Other Comments: not sure on other states, but in NSW you will need to get your car registered as a 2 seater if you plan on driving it on the streets like this.
Aim: remove rear seats, pretty simple.
Required: 10 mm spanner (a 10 mm socket will make it easier though)
Steps:
1. undo velcro from boot lining.
http://i11.photobucket.com/albums/a196/endlessxdespair/car/100_7611.jpg
2. undo bolts on right side seat.
http://i11.photobucket.com/albums/a196/endlessxdespair/car/100_7612.jpg
http://i11.photobucket.com/albums/a196/endlessxdespair/car/100_7613.jpg
3. push seat forward and lift out.
http://i11.photobucket.com/albums/a196/endlessxdespair/car/100_7614.jpg
4. undo bolts on left side seat.
http://i11.photobucket.com/albums/a196/endlessxdespair/car/100_7616.jpg
http://i11.photobucket.com/albums/a196/endlessxdespair/car/100_7619.jpg
5. angle seat as shown then push to the left.
http://i11.photobucket.com/albums/a196/endlessxdespair/car/100_7620.jpg
6. there will be one bolt holding down the bottom part of the seat, undo this and lift/wiggle seat until it pops out.
http://i11.photobucket.com/albums/a196/endlessxdespair/car/100_7622.jpg
http://i11.photobucket.com/albums/a196/endlessxdespair/car/100_7625.jpg
7. once you have removed the boot lining and space saver it will look like this.
http://i11.photobucket.com/albums/a196/endlessxdespair/car/100_7630.jpg
Other Comments: not sure on other states, but in NSW you will need to get your car registered as a 2 seater if you plan on driving it on the streets like this.