relocating number plates

[MWAKU]

i want to relocate it the side like everyone else does, how you do it?

n when u move it, the old location, has like bumps and screw holes for the plate, how do i get rid of it, would i need 2 sand it down, then respray the bumper?

[vinnY]

you can make up a plate from bunnings and just mount the plate on it

you can either leave it or you can shave it, then respray the bumper

would be funky if you could get something made up like the team integra (http://www.team-integra.net/misc/store/images.asp?ItemID=3) license cover hole cover

[simonnowis]

as vinny said theres those L brackets you can buy from hardware shops, theres ones cusco make but too expensive for a piece of metal pretty much the same thing as the L brackets.
otherwise you can use zipties.

[vinnY]

you can pickup those L brackets from bunnings with pre-drilled holes for like $2 or something

actually i got one at home, if you want it come and get it :)

[Zdster]

i want to relocate it the side like everyone else does, how you do it?


Trend setter ey?

[simonnowis]

Trend setter ey?

trend follower lol

[z3lda]

Honda sells plugs for the holes in your bumper bar.

[vinnY]

zdster, simonnowis, let the man do what he wants
if he thinks it looks good then it doesn't matter if he's just following the trend

[rayb3na_]

drill into the front bar..

[An41]

hope theyre not yellow plates

[est1989]

lol just leave it whre it is trust me you'll regret relocating it.
lol

[CB7_OWNER]

For the holes.. you can putty it up, smooth it up wif careful sanding....and then colour over it with matching colour.. clay it, polish, and should be very hard to notice

[z3lda]

For the holes.. you can putty it up, smooth it up wif careful sanding....and then colour over it with matching colour.. clay it, polish, and should be very hard to notice

why waste all that time and effort when u can just buy the plugs from honda?

It cost like $10 lol.


OP, what colour is ur car?

here are the part numbers of the most comon colours,

Front License Plate Plug (Captiva Blue) 90672-SB2-670ZV
Front License Plate Plug (Frost White) 90672-SB2-670YA
Front License Plate Plug (Milano Red) 90672-SB2-670YE
Front License Plate Plug (Granada Black) 90672-SB2-670YK


http://i9.photobucket.com/albums/a83/qtmac_mien/parts/Licenseplate.jpg

[MWAKU]

lol just leave it whre it is trust me you'll regret relocating it.
lol
LOL, i don't trust that red rectangle :X

Thanks everyone. Yeah i'll probably just think about it, drill into the bumper..

But you know where the original location is, isn't there like a rectangle thing that sticks out, with holes? or will it just b two holes??

[MWAKU]

OP, what colour is ur car?

here are the part numbers of the most comon colours,

Front License Plate Plug (Captiva Blue) 90672-SB2-670ZV
Front License Plate Plug (Frost White) 90672-SB2-670YA
Front License Plate Plug (Milano Red) 90672-SB2-670YE
Front License Plate Plug (Granada Black) 90672-SB2-670YK




No idea. Its like a light blue. I'll have a look 2night but yeah. I need some plugs for my rear, i took the honda badge off, and its covered in blue tape atm. LOL. and the glue isn't coming off =\ is like super glue. and the front, no holes.. but .. glue marks still kinda there.. i was heating up the back one with my feet heater, and then i just slighty put my finger nail between the badge and boot, and it just came off .. cheap shiet lol

btw where to pick up plugs like that in sydney? honda dealer? or whaaaat?

[blahZ]

cable tie like me

[simonnowis]

by rectangle thing you mean the metal mount? if so they comes off as well, its just two holes that are bit bumpy.
personally incase you regret it, i would zip tie it to the grill.
for the rear badge correct me if im wrong but i dont think they have any plugs for those small holes, you would prob have to weld the holes and repaint it.

[z3lda]

by rectangle thing you mean the metal mount? if so they comes off as well, its just two holes that are bit bumpy.
personally incase you regret it, i would zip tie it to the grill.
for the rear badge correct me if im wrong but i dont thing they have any plugs for those small holes, you would prob have to weld the holes and repaint it.

The rear bar/boot lid will require welding of the badge holes to look flush.

Those OEM Honda plugs are only available for the fronts

[simonnowis]

The rear bar/boot lid will require welding of the badge holes to look flush.

Those OEM Honda plugs are only available for the fronts

yeh though so :thumbsup:,
just curious would cops in general harras you about the relocated number plate, claiming visibility blah blah blah....

[z3lda]

yeh though so :thumbsup:,
just curious would cops in general harras you about the relocated number plate, claiming visibility blah blah blah....

i've had my plates relocated for the last 3 years

aslong as its visible for oncoming traffic, you'll be right.

i've drive alot of RBT and also been pulled over by alot of unmarks.

they dont say anything.

[finalazy]

why waste all that time and effort when u can just buy the plugs from honda?

It cost like $10 lol.


OP, what colour is ur car?

here are the part numbers of the most comon colours,

Front License Plate Plug (Captiva Blue) 90672-SB2-670ZV
Front License Plate Plug (Frost White) 90672-SB2-670YA
Front License Plate Plug (Milano Red) 90672-SB2-670YE
Front License Plate Plug (Granada Black) 90672-SB2-670YK



have you got the part number for silver?

i bought some L brackets but then i didnt wanna drill holes in my bumper incase i ever changed my mind so im using cable ties now. Also moved it because one of the backing plate for the screws fell off and i lost it.

[z3lda]

have you got the part number for silver?

i bought some L brackets but then i didnt wanna drill holes in my bumper incase i ever changed my mind so im using cable ties now. Also moved it because one of the backing plate for the screws fell off and i lost it.

Front License Plate Plug (Vogue Silver) 90672-SB2-670YV