EG Brake Upgrade... exactly!

[iijjee]

So I'm after exactly what I need to upgrade my 23?mm EG Vti brakes to some 262mm EK4 or DC2 front dics. The rears are fine but the car just doesn't pull up like it needs to and the spongy pedal is unsettling.

I am after all the info I can gather about what I need to buy (and where I can get it if possible, too!) so that when I put the car in to change it all over I can be confident the car will be done (exactly right) a few hours later when I pick it up!

I have been told you need the whole "knuckle assembly"... what is that!?!?!?

I have been told that Bendix Ultimate or green stuff pads are the biz.....?

I have (today) had the brakes checked and they are fine in terms of disc life, and pads are only a smidgin off neweys. The front discs are around the wrong way (RBA with dots and curved grooves pointing the wrong way!) but are in good nick.

Please tell me exactly what I will need...

where I should hunt for it all...

and what to be aware of in terms of issues or potential problems...

Thanks !!!

I want to do this in the next week before I have to go back to work.

[BluEG]

you need the front knuckles off a ek4/dc2 (where the caliper connects to the hub area),calipers to suit, rotors,
and brake master cylinder/booster to suit the bigger brakes.

[bennjamin]

yup as above.

the "knuckle" is the metal arm which connects to both the UPPER and LOWER control arm. The brake hub plus disc n caliper is connected directly the the knuckle.

The reason you need a new knuckle , is because the 2 mounting holes for the larger discs (262 or 282mm) is slightly off the standard eg knuckle (for 242)

[mocchi]

thousand words, hopefully.

http://i516.photobucket.com/albums/u323/breadbaconncheese/aa.png

[thepope1986]

will the Ek knuckle bolt straight up? is there any differences apart from the caliper mounts?

[riruiz_88]

yes it will bolt straight up, only trouble you may have is the brake line being like 5-10mm too short for the EK/DC2 caliper. and you should really upgrade your booster and master cylinder aswell to EK4/DC2

[thepope1986]

hmm.... i think i might have to do this upgrade. a quick jobie for enzed should do the trick (for the lines)

[eg5civic]

i was also thinking of upgrading but i was gonna go for a complete ITR assemlby swap...

would the 96 spec 4x114.3 hold up to track work (as rarer wheels come in this pattern) or should i go the bigger braked 5x114.3

[Sir_vtec]

they are fine as long as u run a decent booster and mc like ek4, dc2, eg6 or itr/ctr.

With some good tyres and brake pads

[Moya]

yup as above.

the "knuckle" is the metal arm which connects to both the UPPER and LOWER control arm. The brake hub plus disc n caliper is connected directly the the knuckle.

The reason you need a new knuckle , is because the 2 mounting holes for the larger discs (262 or 282mm) is slightly off the standard eg knuckle (for 242)

benjamin do you know what the cheapest way to run ITR 282mm rotors but keep 4x100?

I already have rear DC2 discs and ITR 1" booster/MC. But front on my EG is still stock so I want to give them a big upgrade but keep 4x100.

Wilwood are too much (too effective, and too expensive). Oh I also need to do 4040 prop valve but I've been too lazy and I'm not sure which one I need because I don't have ABS and apparently the 4040 prop valve is for ABS?

[jdm_b16a]

Do you know what the cheapest way to run ITR 282mm rotors but keep 4x100

Get DBA200 rotors from SCA, Repco etc. They are 282mm, and have them redrilled for 4 x100. This is a better alternative to getting Prelude VTEC rotors as they are, in my experience, nearly always worn fairly well and leave a lip on the outer edge of the rotor. New DBAs are a better alternative.

Then get the 92 - 95 Accord wagon calipers and brake lines. These are big calipers that should bolt directly to your EG knuckle.

The calipers will have 17CL15VN stamped on them - don't get the 17CL14VN ones as they are standard.

Add some performance brake pads and brake fluid, and you will have enormous stopping power.

Peter

[Sp00ny]

So I'm after exactly what I need to upgrade my 23?mm EG Vti brakes to some 262mm EK4 or DC2 front dics. The rears are fine but the car just doesn't pull up like it needs to and the spongy pedal is unsettling.

A spongy pedal is most likely due to a defective master cylinder. Unless the pedal becomes spongy after sustained heavy braking in which it is more likely to be the pads/rotors.

Just something to think about.

[VT3C]

yes it will bolt straight up, only trouble you may have is the brake line being like 5-10mm too short for the EK/DC2 caliper. and you should really upgrade your booster and master cylinder aswell to EK4/DC2

that's exactly what I was going to say - I've upgraded to EK4 fronts a couple of years ago.

[Rivic]

so many options hrere and im in the same boat upgrading mine atm,
so 262/282mm rotors,
get either DC2 or EK4 knuckle (which is just that arm?)
and bolt straight in?
may need brake lines?
that's it done, dusted nice set of rotors behind wheels yeah?

[riruiz_88]

^^yeh dude thats it, and maybe get some screws from honda that hold the rotor to the hub. mine had some sort of silicone/sealant on it, so just drilled them out and used the new screws

[Rivic]

can someone tell me if a EK1 knuckle is the same as a EK4? mym ate is wrecking a ek1 would be cheaper for me to be baleo to use his arm..

[bennjamin]

most EK1 front knuckles are almost exactly the same as the ek4. Correct me but its the ek1 sedan , and later hatch model too that have it.
Same brake caliper , disc and pad too.

[Rivic]

yeah is a sedan and so is my eh so was thinkin should work?.. will just try

[vinnY]

anyone have an approx price they paid for the dba200 rotors from sca?