Diy: Ctr/ek9 Door Trims!!! In 9 STEPS!!
Disclaimer: The following is provided as a GUIDE ONLY, and neither myself nor Ozhonda take any responsibility for the outcomes of someone else doing the following. You follow these steps at your own risk!
Heres my first Diy that im posting up, hated the look of the ugly stock civic door trims and been meaning to retrim in red suede to match my recaros that will be put in. it actually turned out better then i was expecting.
YOU WILL NEED:
-screw drivers
-red suede or material you want trimmed
-scissors
-bond adhesive(max bond)
-strong solid adhesive (megapoxy)
-hack saw
-sandpaper
STEP 1: Take door trim off (total of 5screws on each side)
1x Behind handle
http://i256.photobucket.com/albums/h...s/DSC00253.jpg
1x arm rest handle
http://i256.photobucket.com/albums/h...s/DSC00252.jpg
3x holding the trim to the door(not the screws holding the speaker)
http://i256.photobucket.com/albums/h...s/DSC00261.jpg
STEP 2: Take plastic behind the side mirror off
http://i256.photobucket.com/albums/h...s/DSC00262.jpg
Once done, pull the trim the pop the plastic pins out, then push up to take the trim off
http://i256.photobucket.com/albums/h...s/DSC00234.jpg
STEP 3: Take Arm rest off, to do this the little donut things must be cut off.
i used a hack saw to cut them off, cuts really easily.
http://i256.photobucket.com/albums/h...s/DSC00239.jpg
once all the donuts are cut, the arm rest should pull out.
http://i256.photobucket.com/albums/h...s/DSC00240.jpg
STEP 4: pull off ugly fabric trim
http://i256.photobucket.com/albums/h...s/DSC00241.jpg
..than use sandpaper to sand off the hairy stuff left on from the fabric, after give it a good wash with water and dry.
http://i256.photobucket.com/albums/h...s/DSC00243.jpg
STEP 5: Cut the fabric(red suede) larger then required.
http://i256.photobucket.com/albums/h...s/DSC00244.jpg
I used "max bond", patiently start from the main surface and stick the fabric on with the adhesive and make sure u spread it evenly to prevent causing lumps. dont stick all at once cuz it may cause wrinkles, start section by section until the fabric is completely stuck on.
TIP: dont use liquidly adhesives as they seem to be soaked into the fabric causing a dark stain. some expensive spray on bonds may be ok.
http://i256.photobucket.com/albums/h...s/DSC00247.jpg
http://i256.photobucket.com/albums/h...s/DSC00249.jpg
STEP 6: Let the glue completely dry and cut the required holes.http://i256.photobucket.com/albums/h...s/DSC00248.jpg
STEP 7: Stick it back onto the door trim and use a strong adhesive,
i used megapoxy, but any solid bond should be good,
(if you dont want the armrest to be permanently stuck on, i guess it may be possible to use short screws and washers where the donuts were to hold it together)
http://i256.photobucket.com/albums/h...s/DSC00256.jpg
http://i256.photobucket.com/albums/h...s/DSC00259.jpg
STEP 8: Let Dry and admirer ur work.
http://i256.photobucket.com/albums/h...s/DSC00260.jpg
STEP 9: Put the trim back onto your door, same way as u took if off but in reverse lol.
BEFORE
http://i256.photobucket.com/albums/h...s/DSC00251.jpg
AFTER
The flash from the camera made it look alot lighter, but its actually slightly darker fabric than the recaros.
http://i256.photobucket.com/albums/h...s/DSC00264.jpg
http://i256.photobucket.com/albums/h...s/DSC00263.jpg
With Recaros installed
http://i256.photobucket.com/albums/h...s/DSC00269.jpg