ED with D15B7 injected wiring help

Hi All,

I have put a fuel injected D15B7 in my ED and have an ECU marked
37820-P06-Q50

i have a wiring loom from an EG sedan and have wired things up to see if I can get it running. I have not wired in the PGFM relay and according to the few diagrams I can find on the internetz regarding the P06 ECU, think I have everything needed.

I can get spark when the car cranks, and I know I have fuel pressure, but it just wont start, or run.

Has anyone done this conversion before? I am sure I have something not wired correctly, and I really need to get this car on the road.

Can anyone point me in the direction of some good wiring diagrams that show what pin is what on the ECU, and being connected to an auto, is there some wires i need to connect to make it think its in park etc so it will allow the engine to start?

Any help greatly appreciated.

Peter has already given up some of his time to help me today, and i went from no spark to now having spark (thanks Pete) but I am just stumped.

Plese help me ECU-Wiring legends!!!!!!!!

Also happy to provide BEER, FOOD, or whatever (some cash) if anyone wants to drop in and have a look what I am missing.

Cheers
Tseesinngwailo

dizzy wired correctly ?
Fuel pump primes....but does it get to the fuel rail ? (crack the fuel line at the fuel filter or at the rail itself slightly to see if its building pressure - fuel will piss out)
PS check this out

OBD1 ECU pinouts and colours....

http://www.phearable.net/tech/wiring...schematics.gif

OBD1/2 dizzy wiring colours

http://media.photobucket.com/image/h...stributors.jpg

yes,check the link ben gave for ecu,
u will have to provide a ground input to pin B7 to fool the ecu into thinking shift lever is in park or neutral.
i take no responsibility for this method,i dont know if your carb shift lever will have the switch on it to do it properly,but u could maybe source a efi shift lever with switch from an ED or EG maybe if u choose to do it properly.

u may also need a brake switch input to ecu as well on D2(12V input) for it to start,just tap off the load side of the brake pedal switch to do it.

that..on a OBD1 auto to manual conversion you take the large single loom located right at the shifter - and directly connect the 2 x Large wires in teh middle , and then connect the reverse switch wires direct from the gearbox to the above mentioned loom to get your reverse lights working too - kinda looks like this
http://media.photobucket.com/image/h...onversion4.jpg

2 large wires are the starter motor feed ben,if the car cranks now then they must be connected or its a manual loom,or am i not reading that right & car is not even cranking?

if its not cranking then good start is what ben said to solve those 2 issues,but u'll still need the ecu ground input as well from shifter.

Hey Guys, Thanks Ben and CRXer, at least I now have some better diagrams to look at..

I have temporarily connected everything, I am just trying to get the car to run before putting everything where it should go.

This is what I have, the loom on the engine has all the right plugs etc

http://gallery.2dingos.com.au/albums..._ecu.sized.jpg

The car cranks fine, it sounds as though its trying to catch, but just wont do it.

I know i have to connect it to the shifter and all, but want to hear it running before continuing.
I have spark, thats definate, not sure , but it looks strong enough.

Covered my driveway in oil before finding that there was no oil pressure sender installed AAGHH :( lucky it was old oil

http://gallery.2dingos.com.au/albums...rrrr.sized.jpg

I think I am maybe missing a ground or safety interlock maybe

I have connected the ground (to simulate shifter) but maybe its the wrong wire?

There is no solenoids on my gearbox, so i have a few plugs not connected, not sure if they should be joined to make a circuit?

At least with your help I am getting there.

Cheers
Tseesinngwailo

The only solenoid on the gearbox is the reverse light switch , won't stop the car from starting. Checked you haven't blown a fuse under the dash when trying grounds or other wires ?

Jason you need the work jus go over and help chris !

Quote:

---

Originally Posted by bennjamin

Checked you haven't blown a fuse under the dash when trying grounds or other wires ?

---

That's what I said! I don't know how many times I've had to search every fuse before replacing one or two when I've been doing the wiring.

Peter

PS. Have a look here Chris:

http://technet.ff-squad.com/

you need to make sure your ecu is wired like this

http://b16a2.kicks-ass.net/tech/gsrwiring1.gif
http://b16a2.kicks-ass.net/tech/gsrwiring2.gif

the above schematic is for a GSR so you ignore Vtec Pressure, VTEC solenoid, IAB, O2 Heater, PSP switch

if you wire it up with the above schematic you will get it running, If your ED was an auto to start with it will already have the Auto inhibiter on it.


also on your picture the top right shows 2 connectors and a bunck of loose wires, those loose wires are ment to go to a 3rd connector that connects to the engine at the LH Shock tower.

Quote:

---

Originally Posted by ECU-MAN

on your picture the top right shows 2 connectors and a bunch of loose wires, those loose wires are meant to go to a 3rd connector that connects to the engine at the LH Shock tower.

---

WHOOPS! Chris, did you cut that connector off when you removed the wiring at PnP? ECU-MAN, we had that schematic when Chris was at my house and we managed to trace the important wires but if that plug is missing ... well ...

Peter

Quote:

---

Originally Posted by jdm_b16a

WHOOPS! Chris, did you cut that connector off when you removed the wiring at PnP? ECU-MAN, we had that schematic when Chris was at my house and we managed to trace the important wires but if that plug is missing ... well ...

Peter

---

well I might have :) I cut the loom that went towards the ignition and fusebox

i know that car is still there, so might go back and pull the rest of the loom, or try to work out whats missing, but thanks for the help guys, hopefully can get this car running :)

I will take some photos of everything and post, someone might spot my ballsup

Cheers
Chris