Trust sandwich plate

Printable View

Show 80 post(s) from this thread on one page

14-07-2007, 06:05 PM
BlitZ

Trust sandwich plate

Ok.. Ive got a trsut sandwich plate..
The sensor holes on the plate are massive and are in metric.

I have guages with sensors in 1/8 imperial..

Where can i get a fitting to plug the sensors into the plate.. (ive already been to autobarn, supercheap, earls and pirtek)

And no i do not want to T off oringal oil pressure sender, drill hole in pan or buy a new sump bolt...

:thumbsup:

Thanks guys..
14-07-2007, 07:13 PM
weezer

Its the same adapter you'd use to replace the oil pan drain plug. Its on the greddy site somewhere. I used a HKS one. I think they're the same
14-07-2007, 07:17 PM
BlitZ

Quote:

Originally Posted by weezer

Its the same adapter you'd use to replace the oil pan drain plug. Its on the greddy site somewhere. I used a HKS one. I think they're the same

i got the sandwich plate here and a spoon sump bolt.. the sump bolt is smaller...if it was the same i would be getting vdo sump sender..

Let me check the website out..
14-07-2007, 09:55 PM
e240

Drop by Pirtek...I go to the one on the way whetherill park, smithfield(?) very helpful.

Quote:

Originally Posted by BlitZ

Ok.. Ive got a trsut sandwich plate..
The sensor holes on the plate are massive and are in metric.

I have guages with sensors in 1/8 imperial..

Where can i get a fitting to plug the sensors into the plate.. (ive already been to autobarn, supercheap, earls and pirtek)

And no i do not want to T off oringal oil pressure sender, drill hole in pan or buy a new sump bolt...

:thumbsup:

Thanks guys..
15-07-2007, 12:39 AM
weezer

Quote:

Originally Posted by BlitZ

i got the sandwich plate here and a spoon sump bolt.. the sump bolt is smaller...if it was the same i would be getting vdo sump sender..

Let me check the website out..

There are different sizes. You just have to find the right thread.
15-07-2007, 12:45 AM
fatboyz39

Yes whetheril park Pirtek. Im sure you'll find the fittings needed there.
15-07-2007, 04:34 PM
BlitZ

dont u guys read eheheh..
Ive been there and so as earls.. heheeh no good
15-07-2007, 04:36 PM
fatboyz39

new sandwich plate FTW.
15-07-2007, 06:45 PM
weezer

Quote:

Originally Posted by BlitZ

dont u guys read eheheh..
Ive been there and so as earls.. heheeh no good

12xP1.25 OIL ADAPTER

Temp. replaces oil pan drain plug
16400713 10.50
14xP1.25 OIL ADAPTER

Temp. replaces oil pan drain plug
16400714 10.50
18xP1.25 OIL ADAPTER

Temp. replaces oil pan drain plug
16400721 10.50
its one of those heheh think its the last one
15-07-2007, 08:48 PM
e240

Quote:

Originally Posted by BlitZ

dont u guys read eheheh..

No, it takes too long, I just read the first line and the last.... :p

Ok, Olympic Instruments - They sell VDO units, they might have the right adaptors. You have to look up the yellow pages, they're in Ryde...
16-07-2007, 06:42 PM
iced

daniel la
autobarn should have the vdo sump plug sender adaptor for under 10$
i may have one lying around im not using
depending on where your sump bolt is on the sump it may not be problem
1/8NPT npz
17-07-2007, 12:06 PM
BlitZ

Quote:

Originally Posted by iced

daniel la
autobarn should have the vdo sump plug sender adaptor for under 10$
i may have one lying around im not using
depending on where your sump bolt is on the sump it may not be problem
1/8NPT npz

its just too messy.. its not something i could live with for the long term.. ...
I am thinking about removing it and making a bun in sump instead...:thumbsup:

Show 80 post(s) from this thread on one page