finally got my ozhonda sticker :) stuck that on and im lovin it.
Printable View
finally got my ozhonda sticker :) stuck that on and im lovin it.
pics of sticker stucked smoothlyQuote:
Originally Posted by Goku
Because drilling a wholeQuote:
Originally Posted by charliebrown
Doesn't prevent water from getting in your car.. And drilling a hole is not a preventative.. Just hides the prOblem .. Which will Most likely come Back to bite you In the ass when the cOnstant moisture behind your tail lights starts to cause rust that will
Not be visible and cause damage in the long term.
Goodluck with that Charliebrown.
When my roof in my house leaks I drill a hole in the floor,then the water runs through and outside again...
buy the gaskets from america, $25ea instead of $50ea here in aus
i have part numbers if needed
Tried taking our my door glass... to no avail? Any tips? I took out the bolts that was holding the glass in place, but i cant slide it out at all
fkn LOL!Quote:
Originally Posted by EKVTIR-T
Replacement radiator cap. I'd replaced the 1.3 Cusco with a 1.3 Mugen as I had a little coolant collecting on the fan shrouds under the filler - wasn't hoses. I noticed that neither was a good fit, instead of lining up parallel to the radiator when on, they twisted a little further. Bought a 1.0 genuine Honda one and noticed the grips were about 2mm longer. fingers crossed it was just dodgy non-OEM. Opened up my air-box - time for a new filter. It's ducted to the lower grille rather than using the factory resonator setup - I need to run some coarse mesh over the inlet pipe I think :)
300 bucks worth of E30 parts arrived for the BMW from the US (cheaper buying and shipping than buying in Aust) on Friday - sadly I won't have much time to play with either car for a few weeks as I have a 2 day conference coming up followed by HSC prac marking which kills my weekends.
Went for a nice sunday drive through the hills with a friend in his GTI.
This is my first Honda. so im new to all this.
Stock standard DC4 btw, only bought it last week, been very happy with it so far.
http://i49.tinypic.com/2zjg9av.jpg
http://i49.tinypic.com/4sjtjp.jpg
ED / DA Arm rest .. FINALLY .. pick it up in day or 2 :)
put my engine in. still got alot to go. i got avid racing torque mounts, which have been fine. and i also bought avid racing 75a or whatever engine mounts and they seem to make the engine notsit as straight as the oem mounts
http://a1.sphotos.ak.fbcdn.net/hphot...31591013_n.jpg
Is that a snail ?
need a new paint job badly!!!!!!!!!!!!!!!!
shieeeeeeeeeeetQuote:
Originally Posted by Lukey
i see turbo manifold and a screamer pipe......i think... lol
inb4 vtec head aswell...
will be on shortly.Quote:
Originally Posted by dc2r-0636
that you do.Quote:
Originally Posted by GSi_PSi
no.
lols.Quote:
Originally Posted by EKVTIR-T
nice stuff lukey
lolwut finally getting some balls lol
wut
Sold it...
Sigh...
suprised you sold it, was very clean! how much did u end up letting it go for?Quote:
Originally Posted by 45SET
Just got the tuning and diagnostic program
So am I actually... as I didn't really want to do it... and the new owner could tell I didn't want to let it go, but had to due to my current position.Quote:
Originally Posted by tripleuse
I sold the car and original engine for very close to the asking price - Which was obviously why I let it go. I'm not going to comment on exact prices, as the new owner is a member on this forum. But it'll more then likely still get about.
thats not to bad then,its a shame however!
I'll remember your car as the car Sydney couldn't produce when I first layed my eyes on it.Quote:
Originally Posted by 45SET
Arm rest looks good, I'm glad it's gone to worthiness.
:) thanks again bruzz .. Will come and chill back over soons .. I just couldnt resist a good wingsuit flying day thats all ..Quote:
Originally Posted by SHOGUNOVDDRK
had another good fly this afternoon weather was perfect :)
Just done custom job eye lids on the DA to see what it look like i got a pic i will post it up later
it was only a 5 minute job .. for a yay or nay ...
http://i1253.photobucket.com/albums/.../Photo0449.jpg
shaved and painted bay :)
http://i1110.photobucket.com/albums/...-mi/yellow.jpg
****ing 89lude always showing us up! hahahaQuote:
Originally Posted by 89lude
haha hardly showing anyone up bro. just trying to share the teg love! :)
**** you... looking good man, i wish i had the patience to shave my bay and respray. :(Quote:
Originally Posted by 89lude
why did you paint it yellow 89
took weeks to do, but don't be discouraged, the hard work pays off! only took us so long because along the way i decided to shave more and more things to a point where i have pretty much 98% of visible holes welded and smoothened out! my hands also fell off with the amount of grinding and sanding :P
and to ekvtir i went yellow because i had yellow paint that i bought for my old teg in the shed lol. must salvage every dollar! :) plus my car is really dark with everything being black wanted to give it some life
ah ok,makes sense lol
what colour is the motor and shit gonna be? something to pop off the yellow aye
idk atm. probably something pretty subtle. the yellow bay is enough colour for my liking
black and yellow hazard stripes on the valve cover.
do it!
started my wire tuck
harness before
http://i.imgur.com/YAIe6.jpg
stripped and labelled
http://i.imgur.com/uOeOd.jpg
part of the charge harness before
http://i.imgur.com/7hTdw.jpg
after sleeving
http://i.imgur.com/xNuCk.jpg
hotness
big job, i wish i had the patience! goodluck!Quote:
Originally Posted by Killa From Manila
where can i buy the sleeving ?
thank-you
Quote:
Originally Posted by Killa From Manila
browsed this guys store on ebay to choose what colour and kind of sleeving i wanted Furryletters ebayQuote:
Originally Posted by na-118
but emailed him to order directly. dmiller108@comcast.net
his direct prices are very cheap and shipping costs next to nothing from the US and only took 2 weeks.
bought this kit of adhesive heatshrink from ebay
and to de-pin the plugs just a $3 set of tiny screw drivers from a hardware shop
looks great
hey guys just need a quick opinion, ive got a bit of paint fade on the bonnet, roof and boot. but the ones on the roof and boot arent that noticeable, should i go for a hood respray or just do a carbon fibre wrap? i know it might not look real but im still a student in year 12 only working 1-2 shifts. so i dont earn a lot. saving up might be an option but its going to take a long time. hahha. cheers
How bad is it? Throw up some pictures manQuote:
Originally Posted by Goku
nice harness......
soupss ozhonda
sure thing. the weather is just horrible atm. once i can get a day where its a bit sunny i definately will. as long as there is no sunlight directly hitting the bonnet, u cant really tell but once u go up close u sorta can tell.Quote:
Originally Posted by Dubstein
I installed ultra racing front strut brace as well as the c-pillar one too. And replaced my k&n pod with a new pod because my one is super dirty...was like that when i bought the car. Might try cleaning the k&n one after seeing how this one goes!
http://i103.photobucket.com/albums/m...6901402305.jpg
I was looking to DIY valve engine cover to blue
and also make that light blue intake pipe black, and if not black I would make it silver?
Any ideas/suggestions? :)
Hey man, I used duplicolour to get mine blue. Works wonders, just the price tag is a bit up there, but well spent IMO.Quote:
Originally Posted by winsto_zuki
http://img844.imageshack.us/img844/267/blueds.jpg
looks good andrew!Quote:
Originally Posted by Tuan94
Nice!
Tax came today! So I wen't a little crazy.
The list of things i've purchased over the last couple of weeks looks a little like this:
- Acura Fog Lights
- SPC Camber Kit
- Ground Control Coilover for my existing koni yellows
- Decided to replace the old and worn bushes in my car, so i bought a full hardrace kit.
- Finally found a good condition set of rears to compliment my 5 stud conversion (already had the fronts).
- DC2R momo Steering wheel
- HEL Braided brake lines
- Slotted Rotors
Cleaned intake manifold - can't decide whether to paint it or not
Before clean
http://img51.imageshack.us/img51/4462/img4145o.jpg
After clean
http://img407.imageshack.us/img407/2027/img4156e.jpg
i rckon some metal polish might get those black marks out
That blue is ****ing sexy. Want something like that for mine. Where did you pick up the paint from? The color code?Quote:
Originally Posted by Tuan94
Its from super cheap mate
Got some CF-48s yesterday soo just been trying to clean them up and finding a place
that does decent price on tyres ..
http://i1253.photobucket.com/albums/.../Photo0467.jpg
http://i1253.photobucket.com/albums/.../Photo0465.jpg
http://i1253.photobucket.com/albums/.../Photo0466.jpg
^ needs original center caps though! they aren't 15's are they?
na 14's and yeh i will try and find the centers .. i got them for $100 :)
Are those Lloyd's old ones?
ahaha yeh mate him and dazz came up yesterday
As viinnh said, just pick it up from your local supercheap or autobarn. Look for the duplicolour range and make sure you grab their primer for it :)Quote:
Originally Posted by eLtrix
after weeks of back and fourth hassel bought my self a like showroom condtion 2001 DC2R with under 100k km's, bought from non p plater mature owner :) didi at top one did all checks on the car everything was to the dot.. no accident history what so ever.. he told me the engine is 100% exceeding what he was expecting.. in saying that was not the cheapest dc2r on the block but was exacly the year colour model condition that i wanted so i had to pay the price, and that will remain unknown :)
http://img228.imageshack.us/img228/2...142656copy.png
Looks really clean :)
Was it $99 999? Haha http://www.carsales.com.au/private/d...1&sort=default
hahahahaha not far off ;) but nah obviously not that much.but i.was open to.a.wide.selection of dc5rs and ep's
Were yu at byp on sunday?
if ur talking to me then no i wasnt never been there lol
Looks mint! Plans?
I remember when mine looked like that 4x4 spec lol
Looks clean!
Keon gym?:pQuote:
Originally Posted by dc2r-0636
Yes :)
Lol Cars looking nice and low, what sussy you got happening man?
Cheers bro! I got BC racing (br series) coilovers
Finally got some time to finish off my engine harness.
Now just need cable and some lugs to finish off the charge harness
http://i.imgur.com/ZSdp8.jpg
http://i.imgur.com/yvqNE.jpg
http://i.imgur.com/Uthhl.jpg
OEM clutch master not even 2 months ****ed up. leaking with in 1 month, completely ****ed in less then 2. ****ing wasted money on OEM and this shit happens.
Bought a OEM clutch master was faulty from factory, swapped for another brand new one and that happens ^^^
How much u spend all up to wrap that harness?