the only reason i wouldnt do it is because of my mates experiences. heat wrap encourages rust. and ive seen the same thing as that ^^^ as well. looks good thugh and it serves its purpose. but i dont have the money to replace headers :P.
alex
Printable View
the only reason i wouldnt do it is because of my mates experiences. heat wrap encourages rust. and ive seen the same thing as that ^^^ as well. looks good thugh and it serves its purpose. but i dont have the money to replace headers :P.
alex
Done that.Quote:
Originally Posted by hitoriko
I'll see how mine goes crazy,thanks mate!
the trick is to clean your headers and spray them with Heat proof paint before wrapping them.
that stops them from rusting.
I usually paint at least 3 coats. Letting it dry between coats (or i cheat and use a blowtorch to speed things up)
Then wet them very damp to stop them from breaking when wrapping. Pull hard on them to get a nice even coverage.
Afterwards i normally start the car to dry up the water.
I've done this on 3-4 sets no issues. Longest lasting one was 4 yrs old.
No, there is no splash tray under there. Why do you ask?
I like the sound of the heatproof paint idea! But i think it would take some pretty extreme paint to take the temps that it would get too under the wrap.
Its quite possible that had i had my timing issue sorted out then there would not have been enough heat there to cause it. However, reflecting on it and knowing what i know now, I would never fit this stuff to a NA car. And would only fit to a turbo if the primarys were going to be long and i was too cheap to invest in ceramic/glaze coating.
i'v'e had my headers heat wrapped. been to track and back nothing wrong with them. keeps temperature down dramatically in the engine bay. i dont see how they can cause a problem. even when your hitting the rev limiter after every corner around the track they held up well. nevertheless good writeup. try soaking the wrap in water first makes it easier to wrap around the headers.
Limbo - thatas the best to do, hitemp heatproof paint, then do the wrap then let dray THEN silicon spray them because this also keeps the water out
forget itQuote:
Originally Posted by crazy2287
everytime i read these replies it makes me want to go outside and finish my set! but its FREEZING outside so i have to wait, worst thing is its halfway done just ahve to wrap 2 more pipes and im done!
i wrapped mine on a hoist, it was a B#$(*@ to get on
Damn Limbo..
So glad I took mine off!
The wrap keeps the headers hot! The hotter the exhaust gas, the quicker it will flow.Quote:
Originally Posted by Mikecivic78
I wrapped my pit bike exhaust in it (I always burnt my leg on it) and then went for a 3 hour thrash with some mates, when i took the wrap off, the exhaust was a purple/blue colour all the way back to the muffler :D Before I wrapped it, there was only about 10-15cm of purple/blue
as the air becomes cool and slows down it will become turbulent and cause lower exhaust velocities and higher pressures. wrapping your zorst to keep in the heat on an NA car has little effect (though it dose have some)
turbos feed off the heat energy in the exhaust gases. so the difference is more noticeable in turbo cars, especially if it has long primary's before the turbine. after the turbine the exhaust gas pressure will reduce rapidly and causes the exhaust gas to cool. this is why large diameter free flowing exhausts are good after the turbo.
could be wrong, been a while since i did thermodynamics. i remember something about gases been thicker, due to the increased collisions of the gas molecules, at higher temperatures. but as long as the gas flow remains laminar there is no problems, thus the reason we try to keep velocity up. once the air becomes turbulent pressures increases dramatically. Ie after the turbine, so rather then trying to restore the laminar flow of the gases, we try to vent to air asap. this is why the turbo will ideally have nothing but a horn on the turbine exit. But i digress XD
That header on the falcon is mild steel is it not ? If it was stainless steel you shouldnt have any worries on it rusting away as stainless doesnt rust.
stainless dose corrode. it is just a lot more resilient.
Not sure of the grade of material in the pacemaker extractors. but definitely some kind of steel.