OK cool, that is a handy chart, PLEASE keep us posted. Did you have any problems getting them to send it to Australia?
Printable View
OK cool, that is a handy chart, PLEASE keep us posted. Did you have any problems getting them to send it to Australia?
No prob at all, it only took 10 days to get here though, as long as you have a credit card with you!Quote:
Originally Posted by xframe88
Im curious about something, every site I read about these interfaces makes reference to using the "factory cd changer port" - Our euros DO have a cd changer, does that mean we need to disconnect the cd player to use the interface.
the factory is in-dash cd changer.... is fine....Quote:
Originally Posted by xframe88
the only thing is... if u have the mp3 player installed... u have to unplug that to use aux in....... check your pm
excellent thanks
http://www.autotoys.com/x/cust/produ...0&cat=0&page=2
It's $88US...not bad but does anyone know how much shipping will cost??
Hey Learner - how hard would you rate the install of the SNHOND3?
Were the instructions clear? Did you use any Honda instructions to remove the trays and compartments etc to gain access to the stereo area?
Finally where did you order it from?
hi yfin... i got it from a frd in america.Quote:
Originally Posted by yfin
the instruction page come with SNHOND3 is useless... it only tell u that u have to connect the SNHOND3 to the factory handunit.... but wat u have to do is just plug it in really.
since there are some ppls pm me how to remove the trays and compartments.. here is the answer.
1. remove the cover near the stick... there are 6 clips holding it. you just have to pull it up with CARE. the yellow dot in the pic is where are the cilps... if i remember it right.
http://members.iinet.net.au/~tommi/ozHonda/ipod/e01.jpg
2. remove the ash-tray (just the tray. [when u wanna clean up the ash-tray].. not the whole thing)
3. after u done step1&2 .. u will see 4 screws holding the ash-tray PART.
the yellow dot in the pic is where the screws are. just un-do the screws then remove the ash-tray part.
http://members.iinet.net.au/~tommi/ozHonda/ipod/e02.jpg
4 now is time to remove the middle compartment (the BOX)... just put your hands to the left and right of the box(INSIDE) then pull it out. just put your hands inside and kinda spread them outwards to go enough pressure, also kind grab on the the lower lip with thumb and forefinger…Don't pull on the door…Be very carefull around the trim as it scratches easily
(there are 2 clips holding the box... is on the left and right side of da box...)
5. plug the cable to here
http://members.iinet.net.au/~tommi/ozHonda/ipod/04.jpg
6. connect the SNHOND3 to the other end of the cable....
7. DONE.
HOPE this will help...
if u still don't understand... maybe is better to ask here... so other ppls can see as well. :D
Learner - thanks! Did the door to "the BOX" need to be removed - or did the entire box come out in once piece?
I am finding it hard to source the device at the moment. Waiting on some emails but at least one place (logjam electronics) do not ship outside USA.
People may find this document useful too. Not exactly the instructions but may assist as the design of the console appears to be similar to ours. Note that I am not 100% sure these instructions are compatible as it is a different vehicle - but it is useful nonetheless.
http://www.handa-accessories.com/accord/04audio.pdf
Guys - I also found this - not the Euro but very similar console design.
http://distantcreations.com/accordipod/
I know this is somewhat overkill - but I want as much information and pictures on this before I start pulling apart the console. If I break something it will be expensive!
the box will come out in ONE pieceQuote:
Originally Posted by yfin
yfin, keep us informed about getting the SNHOND3. I'm interested in getting one soon too.