Printable View
inStalled my Stoptech BBK. took about 1.5 hrs
Just need to bleed the brakes and bed in the pads and rotors.
http://img713.imageshack.us/img713/6425/imag0066tf.jpg
http://img849.imageshack.us/img849/1969/imag0069gw.jpg
http://img809.imageshack.us/img809/7580/imag0074rv.jpg
HUGEEEee
How much was the bbk from stop tech direct? Or distributor thank you
Rebuilding shafts, more tig
i did an order thru BYP, they set me up with this kit and i must say it was a good price.Quote:
Originally Posted by na-118
waiting for september to order..........something
http://farm9.staticflickr.com/8448/7...42c71af1_c.jpg
Had a major service done, nothing too exciting.
Unrelated to thread, but does anyone know a cheap place for closed door resprays?
installed koni yellow shocks with ground control sleeves and a 15mm em1 rear swar bay
http://i1087.photobucket.com/albums/...2/IMAG0533.jpg
http://i1087.photobucket.com/albums/...2/IMAG0577.jpg
http://i1087.photobucket.com/albums/...2/IMAG0545.jpg
please give feedback on this set up as I'm looking at getting Koni sport shocks and Ground Cont as well for EK1
Cheers
i only had a quick drive last night but feels alot firmer without being stiff or bumpy, body roll has been reduced heaps which is great as my ek is full of deadening and audio gear so was getting a bit fat n rolly in the corners. height can be adjusted from stock to sitting on its balls, havent played with the damper adjustment yet ive just got it on 1 full turn from soft and seems to be alright but ill dial it in over the next few weeks.Quote:
Originally Posted by subie
http://i.imgur.com/U3KSV.jpg
whats going on here?
I edited out some numbers incase someone yells at me for posting fulling thing but they are both the same front and back and rego stickers are the apparently same aswell.
i see this around lidcombe lolQuote:
Originally Posted by unl3a5h
went to eastern creek drag way last night ran a 16.1 down the quarter mile.
does any one know if that's any good for a d16y4? been doing some research but can only find times for d16y7
got my rebuilt shafts back, installed them
put everything back together
added some fresh oils and coolant
it turned over just fine
needs new thermostat so that's tonights mission
high to mid 15 seconds if u can get a good launch on good tyresQuote:
Originally Posted by ROM30S
installed the lexan windows on the doors of the EK getting ready for Nationals
lol the silver one was getting a rebuild at lidcombe good friend of mine and the green one got new wheel studs from their....then about 20 minutes after leaving was totaled not his fault lady pulled out from left street turning right as soon as he got to her... *facepalm*lucky the bbs's were in the boot now for sale if anyone is interested will put a for sale thread soon.Quote:
Originally Posted by Glocker
NO frigging way!!! I just saw the green one like 2 weeks ago! Specs on wheels brahQuote:
Originally Posted by unl3a5h
lololQuote:
Originally Posted by ROM30S
An EW2 from an AH got 15.6-15.7
It's about practice yo
Beeza got a 15.8 on his auto sedan man.
Yeah bought an EK Perry. Something to drive around during the week without worrying. :)Quote:
Originally Posted by Perry
Still in the game man?
Noice mun
Thanks Lloyd :)
its been a while. still playing around with cars dude?
Ozhonda is dead quiet now compared to 4 years ago LOL
Yeah man it has.Quote:
Originally Posted by aowwllan
I got an EK last week lol
It is man, especially up here in Brisbane.
Well let's make it louder Lloydy hahahahahaQuote:
Originally Posted by SHOGUNOVDDRK
Buddyclub dual bend short shifter and energy suspension shifter bushings.
15x7/8 i think (could be 6/7) and +20 offsetQuote:
Originally Posted by Glocker
http://img401.imageshack.us/img401/5...0817153059.jpg
:( :(
How much does your mate want for the entire wreck? What condition is the engine in?Quote:
Originally Posted by unl3a5h
engine is still good from what we could see bonnet remained on, when it comes back from insurance we will have to check it out make sure engine hasnt been pushed back but looks like just the radiator is gone (obviously lol) and have received alot of interest so will let you know
dat camber on odyssey
Its called stance
Wash, claybar and wax. Worked the entire afternoon and had to rush the wax job as it was getting dark. 5+ hours of solid work, I can't imagine how people do car detailing for work!
Gave him a wash!
http://img.tapatalk.com/7af89c09-bcbe-3656.jpg
^ I want your number plate so badly :/ ..
Lol actually? It's standard rta issue
Even better LOL. lucky. shits and giggles with the viet boys.
drove mine around the block, everything works well, taking it to get the s/s 2.5" cat back exhaust made up in a few weeks
http://i224.photobucket.com/albums/d...p/IMG_1112.jpg
Great to finally see it in there ryan
after how many years of shit talking :/Quote:
Originally Posted by 90LAN
What's caclon mean??!!!
+1 lol we aint all viet...Quote:
Originally Posted by Hellomotog
Bu cac
Whatt?!?
cac nhỏ
New powersteering pump, wheel bearings, clutch bearing, brake pads, oils, fluids, spark plugs etc.. general prep for blue slip.
http://img21.imageshack.us/img21/8592/photo32rt.jpg
http://img600.imageshack.us/img600/9652/photo31g.jpg
Bleed the brakes, finished off the lexan windows and took some angle out of the rear wing.
Still need to bed in the brakes and do alignment, then im ready for Nationals.
havent posted in ages!
i think this is rather self explanatory haha, never goin back to a inner city meetup :/
props to the photographer, really liked how it turned out :D
http://img818.imageshack.us/img818/1...6254897617.jpg
thats a great shot!
Fuaarrrrrrrrrr, legit photo!Quote:
Originally Posted by mugen_ctr
That photo is sweet as
I got this stupid ass list today.
I'll go elsewhere for my roady because I know it'll be less hassle.
http://a2.sphotos.ak.fbcdn.net/hphot...12410192_n.jpg
most of thet is BS.
LOL at number 7
ordered something, 10-12 week wait, should be sweet when it arrives
Buffing him!
http://img.tapatalk.com/31b043d5-be09-3f53.jpg
http://img.tapatalk.com/31b043d5-be1f-11e2.jpg
http://img.tapatalk.com/31b043d5-be30-cb21.jpg
http://img.tapatalk.com/31b043d5-be3f-18cc.jpg
Gonna do final polish
Then wash and dry
Then lime prime
Then wash and dry.
Then wax
10 hours and still going !
Holy shit, nice man^
Anyone heading to downshift today?
fuarrrk thats dedication right thereQuote:
Originally Posted by Hellomotog
Sounds like JDM :) ... any clues???Quote:
Originally Posted by Niko
lol not clues, havn't seen it on an EK in syd/aus yet that l know ofQuote:
Originally Posted by Alvis
detailed engine bay
http://i144.photobucket.com/albums/r...9-01163016.jpg
Damn that's hot
Hey brother what products are you usingQuote:
Originally Posted by Hellomotog
My ek is about ready to pick up.
It was masked and rubbed back on Friday.
All trims will be painted, now I think I should buy her some new shoes and give her some low
Love the OEM styleQuote:
Originally Posted by 90LAN
^ love the OEM Honda sticker on the airbox :p
Tried replacing wiper blade inserts. The metal pieces keep falling out!! Help? :confused:
hey man. my mate provided them all. shampoo was dodo. clay bar was dodo. then dodo wax at the end. the polishing compounds are menzerna. using festool polishing pads. using 2 bucket system obviously to wash aswell. any other questions just shoot me a pm and i will ask my mate.
ye happenened to my front windscreen wiper. throw them out ASAP. mine came off and left a tiny scratch on the windscreen. just go buy those repco flat wipers they really good. more pricey but.
quick wash and put on my rear lip + boot lid spoiler
http://i480.photobucket.com/albums/r...3/IMG_2953.jpg
http://i480.photobucket.com/albums/r...3/IMG_2946.jpg
managed to destroy a front abs sender, looked under the car to service the transmission and see a huge bundle of copper wire around the driveshaft abs ring area... hilarious
mustve had a rock or something under there
Take my Ek1 to the Brisbane city council rubbish tips, found out my car with 1/4 of fuel left, weight roughly under 1100kg without me in it. With all the add on mods the car carry, I am surprise still weight under 1100kg.
What mods are on your car to weigh 1100? Gli or cxi?
For that comfortable feeling - OEM Ek Armrest
http://i1139.photobucket.com/albums/...h/photo-97.jpg
I've always wondered, dafaq are those holes around the handbrake for? inb4 commo power window conversion.
Ek cxiQuote:
Originally Posted by Hellomotog
Jap spec B18c TypeR engine with 4.7FD LSD Gear box
Rx7 Fc front brake calipers conversion with 282mm brake rotors
Dc2R rear brake calipers conversion with 262mm brake rotors
Ek9 front strut brace
aircorn
recaro sr3 x2
Top fuel air intake,
Whiteline front and rear sway bars + rear subframe brace
15" aftermarket rims weight about 5.9kg each.
I think that all, rest of the mods, I don't think going to make any difference for the weight of the car.
Ps I haven't strip the car at all. The car still got the rear seat, all the carpets, Heavy rear parcel tray, spare tyre......etc.
took some pics of my ek at the painters
http://i1085.photobucket.com/albums/...86735349_n.jpg
http://i1085.photobucket.com/albums/...55542557_n.jpg
Is it just me or are they really small pics?Quote:
Originally Posted by THE 2BSEEN
Anyways I cleaned my baby today. RPF1s are a bitch to clean. But they come up good with a little shimmy shimmy yal
Attachment 22858
They taken off my phoneQuote:
Originally Posted by AndreaCivic
Put a CD player in and while I was doing that discovered that there was a aftermarket alarm.
I had no remotes or key to disable the siren so it started going off as soon as I unplugged it.
Had to scramble to unbolt the siren and dunk it in a bucket of water to shut it up haha
looks nice anyway man, some bigger pics would be great though.Quote:
Originally Posted by THE 2BSEEN