h22a conversion

Printable View

12-01-2009, 07:27 PM
teg94

h22a conversion

i have read numerous DIYs for h22a conversions....

can someone please confirm that if i drop a h22a into my EG, using hasports, that the driver side original mounts need to be cut to fit the engine in...

i want to confirm this before i go ahead hacking that mount..

thanks.
12-01-2009, 07:41 PM
fatboyz39

Pretty sure you have.
12-01-2009, 07:58 PM
teg94

yes i have decided it has to go....

can someone please tell me whether i need a conversion harness to connect the ecu 95 EG (breeze) to h22a??

if so, where can i get one?
12-01-2009, 08:00 PM
SuiJin

http://www.civicland.com/forum/honda...swap-info.html

read this one its the best h22a conversion post ive seen.
12-01-2009, 08:12 PM
barefootbonzai

Quote:

Originally Posted by teg94

yes i have decided it has to go....

can someone please tell me whether i need a conversion harness to connect the ecu 95 EG (breeze) to h22a??

if so, where can i get one?

You're gonna an awsome time doing the conversion if your car is a breeze. You need to change a lot of wiring, join up some fuel lines and change your fuel tank in addition to the link above.
12-01-2009, 08:22 PM
teg94

fuel system is done already...
12-01-2009, 09:27 PM
barefootbonzai

Quote:

Originally Posted by teg94

fuel system is done already...

well done...
12-01-2009, 11:15 PM
jdmTYPE R

and subframe is different with breeze, u will have problem bolting up the rear mount
13-01-2009, 08:37 AM
Benson

Quote:

Originally Posted by jdmTYPE R

and subframe is different with breeze, u will have problem bolting up the rear mount

??? Never heard of this? got any links ?
13-01-2009, 09:16 AM
mr180sx

Quote:

Originally Posted by jdmTYPE R

and subframe is different with breeze, u will have problem bolting up the rear mount

never heard of that one as well. pretty sure all eg chasis is the same. just have to remove driverside mount.

if you have a breeze good luck.have fun taking dash out. hehehe:thumbsup:
13-01-2009, 06:19 PM
teg94

rear mount went on fine - had no issues with that one...
15-01-2009, 09:07 AM
jdmTYPE R

Quote:

Originally Posted by Benson

??? Never heard of this? got any links ?

there is no link i worked on it and rear mount doesnt line up to the bracket hole ives done couple it they never lineup, GL onword is fine only breeze is different ,the mount sit about 1cm away then normal eg does...had to change the subframe from a gl onwards ...even GPC told me its different in the first place and i didnt believe him until i worked on it

Quote:

Originally Posted by mr180sx

never heard of that one as well. pretty sure all eg chasis is the same. just have to remove driverside mount.

if you have a breeze good luck.have fun taking dash out. hehehe:thumbsup:

thats what i thought was wierd to....the mount hole with the braket hole was way off...this was with all of the breeze i worked on..

Quote:

Originally Posted by teg94

rear mount went on fine - had no issues with that one...

mount will bolt onto the subframe fine but getting the bracket to line up to the hole might be a problem..
15-01-2009, 09:43 AM
zco

im sure benny worked on a breeze and didnt have to change it.. hmmm
18-01-2009, 03:05 PM
teg94

does anybody know whether the fuse box needs to be relocated in the EG?

would i need to swap the entire prelude loom in or just use bits of it?

which harness convertor do i need from a EG Breeze 95 to wire it to a H22a?