XFORCE Exhuast systems and headers for Honda Civic EG, EK & EJ Review

Xforce exhaust systems are designed to be a true bolt-on option and power gainer. All exhaust systems are R&D in-house and dyno tested with proven power gains. 304 Stainless steel mandrel bends, and flanges are used in the construction for its strength, excellent heat resistant,, rust proof, high flow (mandrel bends) and finish properties. Everything in the Xforce range includes bolts, nuts, gaskets and everything else needed for a true bolt on experience.

Xforce recommends a dyno tune after an exhaust item has been upgraded (like any other power mod) to fully utilize its power potential.


Cat-Back System for EG, EK & EJ

Model: EG & EK Hatch Back and Sedan
Designs:
1)Cannon Rear Muffler: 60mm pipe diameter; Maximum Power; Racing Sound
2)Twin Loop Rear Muffler: 60mm pipe diameter; Maximum Power; Lower Sound output than Cannon muffler; No obvious exhaust noise from cabin on low and mid rpm; Quicker throttle response.

http://i762.photobucket.com/albums/x...rce/honda1.jpg

http://i762.photobucket.com/albums/x...rce/honda2.jpg

http://i762.photobucket.com/albums/x...rce/Honda3.jpg

http://i762.photobucket.com/albums/x...rce/Honda4.jpg

Header (EG/EK D15/D16)
Model: EG-EK B16 engine
Designs:
1) 4-2-1: 38mm-42mm-60mm;increase mid- range power, improved drivability
2) 4-1: 42mm-63mm;Maximize top end power output.

http://i762.photobucket.com/albums/x...rce/Honda5.jpg

http://i762.photobucket.com/albums/x...rce/Honda6.jpg

Video: Twin loop sound clip

http://www.youtube.com/watch?v=VFZYU...eature=related

Hi,

Will the twin loop system fit the OEM header of an EK4 (diamete: 50 mm)?

Thanks

Hi Sam .

twin loop cat back system should fit oem cat.

Can you confirm that the inlet is 50 mm of the cat back system (I got an OEM header and I will use a 5zigen decat that is also 50mm)?

How much for the system shipping to New Caledonia?

the xforce twin loop cat back to suit an EK is 60mm with a 3.5" tip. it is design to suit the standard honda oem cat. as long as the your decat is design to suit a oem system everything should bolt up. however xforce can not guarantee its system will fit other brands.

best bet would be to also purchase a high flow xforce cat to suit. For delivery cost please contact xforce directly

email: inquiry@xforce.com.au
Tel: 02 9793 7338

Ok thanks I'll hit them up!

hi mate, how much can you do a header for b18c2 on eg?

cheers

hey how much for 421 headers and catback for em1 b16

both have pm

Can u get dc5 header? If so, what's the prices on the 4-1 and the 4-2-1? and are they in stock?

only 4-2-1


RRP 650 .

Did you told a price? I'm looking for the same thing

which one ?

Quote:

---

Originally Posted by matespace

which one ?

---

for extractors for a b18c in an EG?

you got pm

Got headers for prelude? how much posted to perth?

which model ?

bb6 vti-r H22Z1

koolo you got pm.

Got b16a extractors?

and

Twin Loop Exhaust.

Both for EM1 vti-r

Cheers,

Yes, we have both those products available from Xforce. Check out our site for some more detailed info. http://www.xforce.com.au/products.ph...Honda&model=19 . Chat soon.

hey, how much would xforce headers cost for an ek d16? will they bolt onto b16/b18 as well?

Quote:

---

Originally Posted by FongPei

hey, how much would xforce headers cost for an ek d16? will they bolt onto b16/b18 as well?

---

Hey mate, mild steel headers start from $300, and stainless items from $480. D series and B series headers are not compatiable with each other, so if you plan on dropping a B into your car, your best bet is to hold off and get a set for your B series! Thanks

60mm is the biggest u can do for eg hatch catback?
Looking for 3inch because I am running turbo b18c

Do you guys have FN2 headers yet? If so please price me up

How much for a 4-2-1 header with high flow cat and a twinloop cat back for EJ8 civic coupe, d16y8 engine?

Quote:

---

Originally Posted by samyip

How much for a 4-2-1 header with high flow cat and a twinloop cat back for EJ8 civic coupe, d16y8 engine?

---

You got PM.

Finally fitted a twin loop x-Force on my LHD EK4!! Very good quality everything fits perfect! Just had to find the right decat and here we go!!!

The sound is quiet just as I wanted it to be!! Very nice for a daily drive!!

can you inbox me a price for a twin loop ek catback system?

pm sent .

hi how much is the cat back with cannon for ej..?

@blu

You got PM.

How much is it for a 4-2-1 header with high flow cat and a twinloop cat back?

i got a 99 EK hatchback with a b16a2

@jekstar

You got PM.

Hi after a high flow cat on its own how much.?

@sakitumi

You got PM.

how much for 4-1 headers with cannon catback ?

EK HATCHBACK B16A2

@jekstar

You got PM.

Pm sent in regards to dc4 twin loop cat back

hi gonna ask again i forgot how much but this time headers 4-2-1 and cat back without a cannon for ej8.. thanks

@blu

You got PM.

whats your price for the 4-2-1 headers for b16a

@ayebaybay

You got PM.

hi, just wondering a price for a full exhuast system to suit a ek4 with a b16a2 engine, i was interested in the
4-2-1 headers, with a high flow catback, and a twin loop. i live in melbourne. thanks

@johnnyboi87

You got PM.

hey buddy..how much for 2000 bb6 vtir headers?
and cat back twin loop muffler?..
and is pickup available in melbourne?...thanks

@vti_ek9

You got PM.