ek4 clusters into an ek1

i currently have an ek1 looking around ebay to find a cluster with a rev tach in it. im only looking for one which have the red line at 7k rpm would these fit into a ek1? engine is still stock (so the d16y4) and would it put anything out?

edit: looking for an ek3 cluster not 4 my bad

Quote:

---

Originally Posted by bladed_yoshii

i currently have an ek1 looking around ebay to find a cluster with a rev tach in it. im only looking for one which have the red line at 7k rpm would these fit into a ek1? engine is still stock (so the d16y4) and would it put anything out?

edit: looking for an ek3 cluster not 4 my bad

---

here.

You can either get ek gli cluster or ek4 cluster. They will be plug and play and the tacho will work, given the clusters are still in good condition. Only difference is gli goes to 8k and ek4 goes to 9k (correct me if I'm wrong)

Use a Gli cluster with factory tacho

You can see the fitting instruction here http://www.ozhonda.com/forum/showthr...from-your-Cxi!

are the gli the same as the ek3? and will it fit into the ek1

this one?

end eric i was just seeing if the ek3 clusters will fit into the ek1

Quote:

---

Originally Posted by bladed_yoshii

end eric i was just seeing if the ek3 clusters will fit into the ek1

---

seemed like you were looking for a Cluster.

all good, good luck, I recommend but a spoon cluster.

cheers man ill have a look around for one they actully look sick

Quote:

---

Originally Posted by bladed_yoshii

cheers man ill have a look around for one they actully look sick

---

Spoon cluster is so rare and costs around $2000. Eric was joking

Just get a Gli cluster,very cheap,easy to fit and factory finish

Get an EM1 Cluster the red line point is 7800rpm and is higher than the EK Gli.

it should be a plug and play item.

Quote:

---

Originally Posted by XB-16-AX

Get an EM1 Cluster the red line point is 7800rpm and is higher than the EK Gli.

it should be a plug and play item.

---

i dont see the point tbh

its a d16 not a b16

gli cluster should be fine.

Quote:

---

Originally Posted by bladed_yoshii

im only looking for one which have the red line at 7k rpm would these fit into a ek1? engine is still stock (so the d16y4)

---

Quote:

---

Originally Posted by XB-16-AX

Get an EM1 Cluster the red line point is 7800rpm and is higher than the EK Gli.

it should be a plug and play item.

---

Whats the point of 7800 red line? :confused:

yeah i was about to say arnt the ek3 clusters red line showing at 6800rpm

Quote:

---

Originally Posted by EKVTIR-T

Whats the point of 7800 red line? :confused:

---

The point is future plans. B/K/Hswap in the future. No need to change cluster then.

Save money and time!

Kill two birds with 1 stone!

Quote:

---

Originally Posted by EKVTIR-T

Spoon cluster is so rare and costs around $2000. Eric was joking

Just get a Gli cluster,very cheap,easy to fit and factory finish

---

yes, i was joking, still nice though.

well tbh i found a type r cluster on ebay for like 300 i think it was haha considering it but yeah i guess your right i should go for the ek4 cluster incase i do end up dropping a b16 into it

Quote:

---

Originally Posted by bladed_yoshii

well tbh i found a type r cluster on ebay for like 300 i think it was haha considering it but yeah i guess your right i should go for the ek4 cluster incase i do end up dropping a b16 into it

---

EK4 or EM1 same thing bud.

Better to be prepared than not.

ahk so theh ek4's are the same as the em1? and yeah thats very true which is why i think ill go the ek4

Quote:

---

Originally Posted by bladed_yoshii

ahk so theh ek4's are the same as the em1? and yeah thats very true which is why i think ill go the ek4

---

Yes the same bra. So EK4 Vti, VTiR same as EM1 Vti, VTiR etc.

What differs between the two series are redline point and max rpm.

You can also fit a CR-V cluster. The orange > blue !