Printable View
hi guys, im looking to buy a set of Red llock nuts (maybe rays if they fit) , my current rims are lenso replicas which need the allen key type lock nuts, will rays fit on these rims? if so which one :S
thanks
heres a pic of my rims :
http://xposed.au.com//photos/resized...2_000_0051.jpg
yes theyll fit, theyre 'basically' universal made to fit all rims.
oo alright so definately fit?
it aint gna be to big like normal nuts?
how are normal nuts 'too big' for your wheel?
they are to fat to fit in the whole!
thats why i wna know, allen key nuts fit coz they are slim.
any1 ?
how bout u measure your slim lock nuts and maybe someone with rays can measure theirs and ull know cause from what i know rays lug nuts are ment to replace the stock ones in width.
it would be 1.5"
these are basically the nuts i got now :
http://www.ebay.com.my/viItem?ItemId=230140916621
they will look good with ur rims :D
hahaha yeh im after red ones! but im not sure they fit, i found some :
http://www.musecret.com.au/category/3
But im pretty sure the normal ones, the bottom which is like a cone is to fat on my rims
P.S they are called lug nuts. Lock nuts have a special key.
If your still struggling autobarn sell lug nuts with a special key which are thin to fit all rims.
In my experience the allen key type have a tendency to break/become rounded. I've had to weld on the allen key twice to get the rims off.
It usually happens cos of stupid tyre places putting them on too tight or they get seized on. Also some of them are just not good quality. If you use the allen key type make sure you inspect them each time to take them on and off to make sure they are not gonna break. And NO you cannot chizel them out as most wheel that need them will not have any room. I spent quite a long time on the prob until i got the autobarn ones
The autobarn ones i had have been the best since, never a prob for like 5yrs now.
which one look better long or short nuts??
ok lug nuts, yeh i know there sh*t, thats why im asking i want to get rays, im wondering if they fit on my rims.
tengsta, i like long but short is aiight.
rays lugnuts will not fit your style of rims. the holes on your wheels are too small for the lugnuts too fit.
the ones you use are sometimes referred to as barrel nuts. you use the allan key that goes INSIDE the nuts to lock/release them, where as normal lugnuts(oem/rays) have the socket set that goes OUTSIDE/AROUND the nuts to lock/release them
long story short. they will not fit
^ wouldnt the Long rays nuts fit? or is it the same shit?
no. rays long nuts arent slimmer than the standard rays short ones. they
re same size with an extension ontop of the short nuts.
knew it! thanks :D
guess im gna have to paint my stuff
** bump ** this 2 yr. old thread instead of starting new one.
I cannot think what colour lug nuts suit bronze rims.... ?? Anyone have any suggestions? Any colour I think of clashes with bronze.
gunmetal...grey
or Project KICS R40 in titanium...
Oh yes gunmetal, excellent suggestion.
Problem is hard to find gunmetal lugs, a lot come in that gay chrome colour
too bad.... i sold my 5zigen ones 20piece... 1 lock each wheel.
goodluck in finding them otherwise try and pick up a RAYS Short gun metal colour might be a bit exp though atm.
Musecret have project kics R40 in gunmetal and titanium.... can you justify the money for them though....
http://www.gotuning.com/images/produ...4.thumb_medium
Oh man I would have bought them off you. Checking out eBay now & it's all so expensive.
What's the difference between open & close ended?
Did some research & for my EG is 12mm x 1.5 yeah? I just need the tuner lugs for aftermarket wheels?
Open end is the Project KIC i posted above and they are considered LONG.
Closed ends and SHORT are these ones below:
http://3.bp.blogspot.com/_JoN9797qIe...0/P1280171.JPG
I am assuming honda's use all the same. So mine were M12x1.5 which should be right, PM someone who has an EG to check if your right with the specs.
Yeh make sure you check the shape of them as well, there are 2 types ROUNDED or TAPERED.
Most Aft use TAPERED but not always. Just check your wheels and get the right nuts.
Hope this has been helpful. :p
I got bronze lug nuts.
used them on my mf-10's
pm me if you're interested.
Are you able to post some pics of them here Bludger? Cheers
last picture in the 1st post.
thats the clearest pic i got.
http://www.ozhonda.com/forum/showthr...=melbourne+cpr
Cheers for that mate, yeah dunno the bronze would suit it that well cause it kinda blends in. Might need a colour that stands out more such as blue or gunmetal as suggested earlier
thats cool, it sounds like you already know what you want.
everyone has a different opinion on what suits.
also depends on the color of the car.
I had red lugs on before this cos my car's red.
now you know what you want, go and get it without wasting more time.
You had the same dilemma i was in.
I was on the verge of getting Anodised RED lugnuts which would have looked sick but ended up sticking with gunmetal to not stand out from the crowd.
Reckon red would go; what colour is your car btw?
Take into consideration the colour of your car; atm i am running anodised blue on time attack coloured wheels looks okay but stands out. :p
http://www.weaksauceparts.com/store/...iles/crkai.jpg
Try picture red lugnuts on this
http://www.boomspeed.com/fnananon/shoot1_2.jpg
red nuts on a red car looks good, i had them
Rofl bludger - hard to find a pic of red lugnuts on a bronze wheel on google.Quote:
Originally Posted by Bludger
red lugs on any coloured car will look good except blue and green.
Other colours will just depend on the wheel colour then.
Yeah I think I'm gonna go with blue, thx for the pics!