[DIY] HID install for dc2r

Disclaimer: The following is provided as a GUIDE ONLY, and neither myself nor Ozhonda take any responsibility for the outcomes of someone else doing the following. You follow these steps at your own risk!

Aim: to install HID kit on a dc2r

Required
- HID kit
- Screw driver
- Spanner

Steps

1. Bend the iron stand about 90 degree and screw on the ballast on the outside of the iron stand using a screw driver to twist the screw and a spanner to hold the nut.

http://i192.photobucket.com/albums/z285/_TanK/diy4.jpg

2. Open the hood and remove one of the chassis bolt by using a spanner on the passenger side and put the iron stand there and screw the chassis bolt back in with a spanner.

http://i192.photobucket.com/albums/z285/_TanK/diy3.jpg

3. Now on the driver side, screw the ballast on existing hole on the chassis which is just under the strut bar

http://i192.photobucket.com/albums/z285/_TanK/diy1.jpg

4. Put the bulb into the light slot and twist to fit tight. Then connect the cables from the ballast to the bulbs


5. Using the Relay Cable, plug one end to the ballast and the other end into the headlight power

http://i192.photobucket.com/albums/z285/_TanK/diy2.jpg

Result

http://i192.photobucket.com/albums/z...K/DSC03380.jpg

http://i192.photobucket.com/albums/z...K/DSC03381.jpg

http://i192.photobucket.com/albums/z...C03383edit.jpg

Other Comments:
Please don't hesitate to ask if you need further advise or help in the matter. Good luck with your installation :)

Plug and play, really.

It's just the matter of finding a suitable place for the ballast.
Most would prefer a stealth install in the fenders or hidden within the bumpers, but that requires more effort.

Well. This does the job anyways.
Good write up.

Quote:

---

Originally Posted by Kazaf

Plug and play, really.

---

Agreed!
There's no way you can get this install wrong!
Great write up.

Don't forget, when install the new HID bulb, DO NOT touch the globe with your fingers!

hey dude, good write up man, try hiding the transformer would be good, incase cops come again ask to pop ur bonnet later, " whats this - shakes shakes "

keep it up... cheers

looks decent dude btw nice writeup
was just wondering which bulbs were they?
4000k? - 6000k ?

[DEFECTS]

nice write up man

good to see that i was able to help

They are 6000k which is diamond white

Quote:

---

Originally Posted by 1900-hustler

nice write up man

good to see that i was able to help

---

Yep thanks for the help hustler

Quote:

---

Originally Posted by kyobibi

Agreed!
There's no way you can get this install wrong!
Great write up.

Don't forget, when install the new HID bulb, DO NOT touch the globe with your fingers!

---

I just installed my HID kit...It took a lot of fiddling because the darned harness and bulbs would not fit like OEM. But I managed to tweak them and make them fit :) Now the lights are working fine, but I have to wait til night time to make adjustments.

Anyway, I had some help from my friend and I reckon he may have touched the bulb even though he said he didn't...whats the worst that could happen?

Quote:

---

Originally Posted by xenonkuraz

I just installed my HID kit...It took a lot of fiddling because the darned harness and bulbs would not fit like OEM. But I managed to tweak them and make them fit :) Now the lights are working fine, but I have to wait til night time to make adjustments.

Anyway, I had some help from my friend and I reckon he may have touched the bulb even though he said he didn't...whats the worst that could happen?

---

Bulb will blow. As your skin contains oil. oil = greater heat on the bulb = bye bye!

depends how he touched it..if its just abit shouldnt do any harm i guess.

i'm sure you'll know if it blows lol

i just fitted mine on Friday... 5000K more oem look loving it!!! =)

if you touch your bulbs with your hand, the life of the bulb will be shorten, not sure will it blow as the oil from your skin decrease the life of the bulbs.

congrats teaserR, hope it looks nice and bright hehe :p

Clean bulbs with Isopropyl Alcohol wipes... thatll get all the oil off, stop them from blowing :D also, if you look at the glass and theres a brown/burnt looking patch, thatd be where he touched them... if not, he didnt touch them lol

much easier to install on the dc3r compared to my s15 where u need a drill

hey
lol
i installed mine
but, they're way to bright ><
i think i'm gonna get defected

any way to make them more dim?

aim/point them down...thats what i had to do

Quote:

---

Originally Posted by vincikwan

much easier to install on the dc3r compared to my s15 where u need a drill

---

lol wth.

Quote:

---

Originally Posted by mr.hieudangly

any way to make them more dim?

---

6000k or 8000k ?

Quote:

---

Originally Posted by mr.hieudangly

hey
lol
i installed mine
but, they're way to bright ><
i think i'm gonna get defected

---

did you buy and install em yourself hieu
i wanna get some

anyone got any tips on how to aim the bulbs? ive got one that is aimed a bit higher lol