DIY: CTR Pedal Installation

Not my write up. I found this and thought it will be useful for others as i looked online for sometime for write ups and couldn't find any. So take a look below:


tools needed:
Drill. ( not sure what size yet, but ill edit later.
Rivet gun.
needle nose plyers.
14mm deep socket.
14mm shallow socket.
ratchet.
3.8 extension.
flat head.
patience.
persistance.
common sense.

Also, IF you're a large person, in any way, by any definition of large, you wont be able to do it the same way.
You'll have to remove the steering column and pull out the entire pedal assembly and brackets. But the good news is, You'll still have to pull out a cotter pin on the clutch push rod.
OK so i know what youre thinking. why hasnt he done all 3?
We'll get to that later.

http://members.aol.com/il2i/pedals1.jpeg

Doesnt really matter which pedal you want to start with, I just started with the accelorator. The first thing you need to do is remover the steering column cover. Just pull on it. It pops off.

http://members.aol.com/il2i/pedals2.jpeg

http://members.aol.com/il2i/pedals4.jpeg

Next you'll want to Disconnect the throttle cable. It slides out sideways. You can do this with your hands.

Then take a flat head screw driver to pry on the cotter pin to straighten it out. Use needle nose to remove the cotter pin and the pedal can be removed.
Installation is the opposite of course.

http://members.aol.com/il2i/pedals3.jpeg

http://members.aol.com/il2i/pedals5.jpeg

Next is the clutch pedal. This is a little more difficult. First remove the 14mm nut pictured. Then put the socket on the bolt on the other side, back it off and tap it out with a hammer.

http://members.aol.com/il2i/pedals6.jpeg

Once that's done you can remove the cotter pin the same way you did on the accelorator. then you slide out the rod for the clutch master push rod.

again installation is reverse.

http://members.aol.com/il2i/pedals8.jpeg



and this is what youll end up with.

http://members.aol.com/il2i/pedals7.jpeg



http://members.aol.com/il2i/pedals13.jpeg



I don't believe the ek9 pedals come with 2 pedals and then just one cover. We get 3 pedals so i removed the section in regards to just drilling into the pedal =P


The original article can be found here : http://www.jdmcivic.com/forums/showthread.php?t=77549

Thanks,

so its basically drilling holes into stock pedals to pop rivert the ctr style pedals in?
where would you get the ctr style pedal covers?

pretty sure JDM yard sells ctr pedals..
good write up dude =] thank you!

i know they sell the pedal kit, which includes the pedal arms. but just the cover?

Quote:

---

Originally Posted by simonnowis

i know they sell the pedal kit, which includes the pedal arms. but just the cover?

---

no no i meant that i removed that section because we here get the actual pedals all three of them. =)

if only it was a matter of drilling that would of made life easier for me ahahah. Yes jdmyard to sell it. :thumbsup:

good write up

So why didn't you do the brake pedal ?

Quote:

---

Originally Posted by VTECACCORD

So why didn't you do the brake pedal ?

---

lol i've done it =P this is just an article i found ahahah. im just bringing it here coz i never saw one wen i was doing mine. =) :thumbsup:

the CTR Pedals are the entire arms for accelerator, brake and clutch. they are no "covers" and a drill is not required.

remove old arms, install new arms. need 14mm spanner/socket, pliers, and gloves or bandaids

Quote:

---

Originally Posted by zco

the CTR Pedals are the entire arms for accelerator, brake and clutch. they are no "covers" and a drill is not required.

remove old arms, install new arms. need 14mm spanner/socket, pliers, and gloves or bandaids

---

I've got my JDM DC2R pedals sitting here uninstalled for well over 3 months.
Just looking underneath the dash scares me.

Quote:

---

Originally Posted by Kazaf

I've got my JDM DC2R pedals sitting here uninstalled for well over 3 months.
Just looking underneath the dash scares me.

---

Your not the only one, I have had mine sitting there for a year. Accelerator pedal was a bitch on it's own. :p

nice knightmare :P

pfft i was told this is hard, might have to recheck my agenda and do this..

bumping this old thread because i installed mine today and it was the biggest pain in the ass! anyone who is considering buying these and installing it yourself - save yourself the trouble.

i removed my driver's side seat to make things easier.

yeah, i thought about doing this, and people just say its a pain in teh ass, so ill just live with the rubber pedals, hell, no one can see them