[DIY] Honda Civic EG - s2000 Start Button Install

Printable View

14-08-2008, 03:08 PM
SuiJin

[DIY] Honda Civic EG - s2000 Start Button Install
Disclaimer: The following is provided as a GUIDE ONLY, and neither myself nor Ozhonda take any responsibility for the outcomes of someone else doing the following. You follow these steps at your own risk!

Tools Required
1. Honda Civic Eg
2. Wire Stripper + Kit
3. s2000 Start Button
4. (Optional) Double Din - Sex Factor
5. Screwdriver

Method
1. Locate your under dash cover (underneath your steering wheel ==;; ), remove the three screws.

2. Presented in front of you is your fuse box, probably some stereo wires for dodgy factor and possible alarm system (get one, do it!).

3. Locate the following plugs. These are the two main plugs which operates your ignition. This means you still need a key for the steering wheel yo!

http://suijin.amestris.com/Honda Civ...82008(003).jpg

http://suijin.amestris.com/Honda Civ...82008(004).jpg

4. Alright we'll start with the second image. The top image displays a plug from the ignition to a portion above the fuse box. With two wires. exiting and entering. One wire being white the other being black and white strip.

5. Strip a part of the black and white wire or slice it apart if you wish to disable key start completely. (Please not do not slice unless you've fully tested its functionality.)

6. Now the first image. The plug has three wires, yellow, white with black strip and black with yellow strip. Start stripping the black with yellow strip wire. (Do not slice - Beware this wire contains a constant 12V therefore do not let it touch bare metal).

7. Alright hoping you have yours s2k button all ready (If you require some help setting up your s2k button message me and i'll post a DIY).

8. On your s2k button there will be three wires leading out of the fuse. 2 Red and 1 Black. Red (30) and Red (87) Black (86).

9.
- Red (30) leads to the wire stripped/sliced on the second image. (Black w/ White Strip.)
- Red (87) leads to the wire stripped on the first image. (Black w/ Yellow Strip.)
- Black (86) grounding, attached this to any metal close by. (Underneath the steering wheel one of the steering wheel cover screws will be fine.)
10. Input your key turn til all electronics are on. This also disables steering lock etc. Test your start button.

Setup example with double din...
http://suijin.amestris.com/Honda Civ...82008(001).jpg

Anyone living in Melbourne feel free to message me to request help on setting this up locally.
14-08-2008, 03:09 PM
SuiJin

Ignore the extra masking tape, I removed my factory alarm system cause the old owner lost the remote for it.
14-08-2008, 03:16 PM
kcokla

cool DIY
wht happens when the car is on and u press the engine button?
14-08-2008, 03:17 PM
SuiJin

It cranks, doesn't shut, its like turning the key again. Not advisable.
14-08-2008, 03:43 PM
mars_panas

Nice work bro.... +1
14-08-2008, 06:54 PM
kcokla

would i also assume if i turned the key fully ( to start ignitition) nothing would happen because its been discnonected there?

ps +1
14-08-2008, 08:19 PM
SuiJin

if u sliced as written yes, if you didn't and just tapped it would start.

Quote:

5. Strip a part of the black and white wire or slice it apart if you wish to disable key start completely. (Please not do not slice unless you've fully tested its functionality.)
19-08-2008, 10:45 AM
SuiJin

roflmao needed to use my own diy thread this morning +1 to me lol.
10-10-2008, 08:56 PM
kairi_k

Nice work Vincent +1 rep
10-10-2008, 11:28 PM
TONTON

Legendary stuff mate

+1 repz y0
05-11-2008, 02:38 PM
SuiJin

This can be used for the pivot set also so i've found, quite similar.
02-02-2009, 11:41 AM
Snax713

can you put one of these on a intergra? is it possible?
DC2
cheers
02-02-2009, 12:22 PM
JasonGilholme

you can do this on any car. Just need to find the correct wires to tap the button into.
02-02-2009, 12:34 PM
nisboi40

would it be the same wires as ej8 coupe
cheers
03-02-2009, 02:27 AM
SuiJin

need to look, but for most cars it practically all the same.
05-02-2009, 08:38 AM
turtle187

awesome DIY, gonna try this on my ek once i get hands on a s2k start button
05-02-2009, 09:34 AM
kriZy

possible on EK4?
05-02-2009, 11:27 AM
Dy_

Quote:

Originally Posted by kriZy

possible on EK4?

yeah it is.
05-02-2009, 11:43 AM
Paul1985

It's possible on ANY car, as long as you find the correct wires and you have a mounting point for it.
06-02-2009, 04:14 PM
sammy342

where can i get one of these buttons are they expensive and in the pic it look like i fits perfect in the cigaret lighter hole
06-02-2009, 09:36 PM
egSi

cool DIY
06-02-2009, 09:44 PM
NightKids

Where would you mount it on my EG because i don't have a double din console...
07-02-2009, 04:20 PM
sammy342

anyone ?? where can i buy a button?
15-02-2009, 11:39 PM
c1v1c

Quote:

Originally Posted by NightKids

Where would you mount it on my EG because i don't have a double din console...

Option A: You could pull out your cigarette lighter and mount it there.

Option B: Perhaps in 1 of the panels beside your steering wheel, you would just have to drill a hole big enough

(Recommend option A)

Quote:

Originally Posted by sammy342

anyone ?? where can i buy a button?

Option A: Alot of the traders here on ozhonda do stock and supply them, PM a couple of them and see what you can find. (A few of them might even be willing to source the parts for you.)

Option B: Ebay has a few, but mainly in America and with the way the economy is these days they will probably cost a bit. (But worth a try.)

Hope this helps you both out and anyone else with the same questions.
16-02-2009, 04:34 PM
sammy342

thanks heaps c1v1c
25-02-2009, 01:17 PM
redefine

heh, nice DIY,
i was going to do this with a push-on (not push-on/off) switch from jaycar, does anyone know the amp rating at 12V the switch needs to be?

edit: i've found a really slick looking spst momentary switch thats rated 8A at 125VAC. would this be enough? link

edit: i did it today with that switch and it works fine! :D

the ek has markings on the back of the key barrel for the wires, for bat, acc, IG(2A), ST and another one which i didnt see...all i did was run a line from battery-switch, and switch to ST (starter motor). works awesome. a nice bit of bling!
15-03-2009, 05:46 PM
redefine

another question, does anyone know the configuration of the barrel, eg. is it possible to use missile switches for accesory and ignition position and only use the key+barrel for immobiliser purposes?
15-03-2009, 06:20 PM
MR-VTEC

post up pics man :)

also, suijin can you reload the images in your original post.

thanks
15-03-2009, 06:42 PM
c1v1c

Quote:

Originally Posted by redefine

another question, does anyone know the configuration of the barrel, eg. is it possible to use missile switches for accesory and ignition position and only use the key+barrel for immobiliser purposes?

It would be possible.. But I not sure the RTA would be happy about it, as I am not sure this kind of setup is allowed in a road legal car.. I could be wrong and if I am someone can set me straight.
15-03-2009, 07:05 PM
trism

i cant see why it wouldnt be

it has nothing to do with the roadworthy of the car.......
15-03-2009, 07:37 PM
redefine

yeah, i dont think it would be illegal.
i guess more specifically, would it be bad to have the key in the acc position (so you could turn the wheel) and a switch connecting the ignition wire at the same time.

i might not end up doing it anyway, the more i think about it, the more i think it might be an annoyance.

anyway pics from my install.

http://i53.photobucket.com/albums/g5...h/IMG_2205.jpg
http://i53.photobucket.com/albums/g5...h/IMG_2204.jpg

and an extra teaser of my next project. currently not done cause i'm trying to source some small but necesary parts. will post a writeup when i'm done ;)
http://i53.photobucket.com/albums/g5...h/IMG_2203.jpg
16-03-2009, 09:38 AM
mohdmanutd

can a fd1 start button be used for this DIY?
16-03-2009, 09:49 AM
redefine

you can use whatever start button you like, as long as its a momentary switch, and theres a spot to mount it
29-03-2009, 12:24 AM
c1v1c

I have recently done this instal into my EG.. I put it in place of the cigi lighter.. But at the same time I have kept the cigi lighter wired up and hanging freely out the back of the centre console (where the aircon vents go to your feet).. Soon ill make a perm housing for it behind there and it isnt just flopping about.. Reason for keeping it was for portable GPS.. Will take some pics as soon as I get a chance for all to see..
17-06-2009, 09:54 PM
mohdmanutd

sorry guys but i cant view the pictures.....any help?
09-07-2009, 10:08 PM
turtle187

guys is it me or i cant see pics for this DIY
09-07-2009, 10:56 PM
vtesh

its you dude,,,,
11-07-2009, 01:43 PM
illuzi0nz

yeah .. i cant see the pics either :(
11-07-2009, 05:15 PM
c1v1c

I can see the pics clear as day. Perhaps you have to clear all the cookies and stuff out of your browser?
11-07-2009, 05:21 PM
SuiJin

im going to upload a new set of tutorials. in the next few days. msg me if ur in melbourne and what help with this. (PM)
19-07-2009, 11:54 PM
burner42

sorry to bring back an old thread, but any chance of updating pics?
14-12-2009, 02:14 PM
Giraffe

sorry to bring a couple month old thread but can you reload the pics ?
14-12-2009, 06:55 PM
SuiJin

ill take photos when slow_poke comes around for me to do it =p
16-12-2009, 12:19 AM
Giraffe

alright wanna take a video also ?
16-12-2009, 09:46 AM
SuiJin

nah not really but if your in melb i can get it done for you lol.
16-12-2009, 03:28 PM
slow_poke

i got burnt like a mother f**k outside suijins house today ahhaa!! Thanks for the install really appreciate it!
20-12-2009, 01:45 AM
connorling

photos dont work!!! please upload again.
where can u get that button?
20-12-2009, 06:49 AM
MR-VTEC

ebay.
20-12-2009, 07:49 AM
kcokla

u can get that button from Jdm-concept in the trader section.