Tucking the washer bottle in a DC2

Printable View

27-08-2009, 03:12 PM
G-Stick

Tucking the washer bottle in a DC2

Disclaimer: The following is provided as a GUIDE ONLY, and neither myself nor Ozhonda take any responsibility for the outcomes of someone else doing the following. You follow these steps at your own risk!

Aim: To Tuck the Winderscreen washer bottle in the gen 3 integra and make it looks more neat.

Required:
10mm socket and wrench
washer bottle from 98 spec jdm ITR
gromet ( which i got from the firewall of my other integra)

Step 1

First that off your front bumper,

refer to this if you dont know how to take it off
front bumper removal

Step 2

Locate the washer bottle on the passenger side of the car
and remove the old washer bottle out. And install the new washer bottle.

http://img111.imageshack.us/img111/44/dsc01238u.jpg

Step 3

98 spec vs 96 spec
Notice how the 98 spec hose is bendable, it can also be detached.
So once u fill it with water detach the hose.
http://img510.imageshack.us/img510/7874/dsc01239cfa.jpg

Step 4
Plug the hole on top of the washer bottle with the grommet from the fire
wall. Surprisingly it fits pretty well :p . It can also be used for the rear wiper
delete if you want to get rid of yours
http://img295.imageshack.us/img295/8656/dsc01240.jpg

And the finish product should look like this

http://img362.imageshack.us/img362/1537/dsc01242.jpg

C&C welcome :thumbsup:

I know the rest of my engine bay looks messy.. ill get to that next time ;)
09-11-2009, 11:24 PM
STiR

How come no one commented on this? Looks pretty cool
10-11-2009, 04:56 PM
Lukey

:thumbsup:
10-11-2009, 07:11 PM
GIPONU

so umm, couldnt we also just chop off that part where the piping meets the container, then put a plug over the top of that so it doesnt spill and use a funnel to fill the container? lol

but anyways, good job buddy
10-11-2009, 07:35 PM
beeza

Good Work!!
12-11-2009, 09:27 PM
MM89

might as well do a/c and p/s delete while you're at it XD
which grommet from the firewall did you use man?
13-11-2009, 09:47 PM
m3ntAL_l2

lol..

i think might be the big grommet on the passenger side firewall next/below to battery
14-11-2009, 06:57 PM
RandyRhydah

nice little trick, will that washer bottle fit up to an eg by any chance?

http://img362.imageshack.us/img362/1537/dsc01242.jpg

lol dont like your power steering pump? looks like youve owned the engine bay wall a couple times with the pulley
16-11-2009, 12:00 AM
MM89

did you take out the B series to try and fit something else in? :P
16-11-2009, 03:48 AM
IEVAQ8

u must have been bored duy.........lol
16-11-2009, 11:05 AM
G-Stick

Thanks guys :thumbsup:

Quote:

Originally Posted by GIPONU

so umm, couldnt we also just chop off that part where the piping meets the container, then put a plug over the top of that so it doesnt spill and use a funnel to fill the container? lol

but anyways, good job buddy

U can but the hole might be too big, i had a spare jdm washer bottle so i did it lol.

Quote:

Originally Posted by MM89

might as well do a/c and p/s delete while you're at it XD
which grommet from the firewall did you use man?

Nah man, value my ac haha

Quote:

Originally Posted by m3ntAL_l2

lol..

i think might be the big grommet on the passenger side firewall next/below to battery

Yea its the one on the left of the battery

Quote:

Originally Posted by RandyRhydah

nice little trick, will that washer bottle fit up to an eg by any chance?

http://img362.imageshack.us/img362/1537/dsc01242.jpg

lol dont like your power steering pump? looks like youve owned the engine bay wall a couple times with the pulley

Not too sure if it will fit the eg's, the scratches were done by the noob old owner :(

Quote:

Originally Posted by MM89

did you take out the B series to try and fit something else in? :P

Yea.. putting in the d series.. lol

Quote:

Originally Posted by IEVAQ8

u must have been bored duy.........lol

i did it when i was installing Milans HID jdm headlights :thumbsup: 2 birds 1 stone lol
16-11-2009, 11:30 AM
EK1.6LCIV

that's pretty cool :)
13-12-2009, 11:20 PM
kairi_k

nice one
13-12-2009, 11:25 PM
kairi_k

my washer bottle has 2 openings at the bottom??? strange
14-12-2009, 06:35 AM
G-Stick

nah.. ones for the front windscreen, ones for the rear. the jdm itrs don't have a rear wiper or nozzle.
14-12-2009, 04:06 PM
kairi_k

Quote:

Originally Posted by G-Stick

nah.. ones for the front windscreen, ones for the rear. the jdm itrs don't have a rear wiper or nozzle.

yeah thats right
03-01-2016, 03:01 AM
3K9

Yo, please fix up pics, I wanna see them.
Thanks.
04-01-2016, 10:54 AM
lolmclol

Could only find three of the images ...

Quote:

Originally Posted by G-Stick

Disclaimer: The following is provided as a GUIDE ONLY, and neither myself nor Ozhonda take any responsibility for the outcomes of someone else doing the following. You follow these steps at your own risk!

Aim: To Tuck the Winderscreen washer bottle in the gen 3 integra and make it looks more neat.

Required:
10mm socket and wrench
washer bottle from 98 spec jdm ITR
gromet ( which i got from the firewall of my other integra)

Step 1

First that off your front bumper,

refer to this if you dont know how to take it off
front bumper removal

Step 2

Locate the washer bottle on the passenger side of the car
and remove the old washer bottle out. And install the new washer bottle.

http://s10.postimg.org/9k290aiq1/image.jpg

Step 3

98 spec vs 96 spec
Notice how the 98 spec hose is bendable, it can also be detached.
So once u fill it with water detach the hose.
http://img510.imageshack.us/img510/7874/dsc01239cfa.jpg

Step 4
Plug the hole on top of the washer bottle with the grommet from the fire
wall. Surprisingly it fits pretty well :p . It can also be used for the rear wiper
delete if you want to get rid of yours
http://s18.postimg.org/71efwvyc9/image.jpg

And the finish product should look like this

http://s8.postimg.org/7512voqx1/image.jpg

C&C welcome :thumbsup:

I know the rest of my engine bay looks messy.. ill get to that next time ;)