pics?
Printable View
pics?
404 pictures not found [emoji14]
My SD card got corrupted a few weeks ago. Lost heaps of built photos =/
But I'll update this tread end the end of this week. I hvnt got time to go to the workshop lately.
After digging a few FB post I have some pictures that may be worthy to share...
I Finally got my shipment of the parts from Japan.
it was bigger than i taught it would.
First of all, I went on a Friday after knock off early from work to the airport cargo area and found out the Ute that i borrowed from my mate, is not going to fit all of the items.
I ended up spending a good hour or so wondering arround the airport complex to get my AirWay bill cleared out form custom
Forwarder Dock - Custom house (custom fee $) - Freight broker (Release fee $) - Custom house (stamp) - dock (wow that is a big packages)
Went back the following day (Saturday) and this time i was well prepared with a 6x4 trailer on tow!
https://fbcdn-sphotos-c-a.akamaihd.n...33d5f3c7209237
https://fbcdn-sphotos-g-a.akamaihd.n...37c4bdc776a1d5
https://fbcdn-sphotos-g-a.akamaihd.n...99f2d2d1db5c64
and i filled them up easy...
Back to the house and start unwrapping my early christmass pressent that i bought for my self...
https://scontent.xx.fbcdn.net/hphoto...43&oe=565CE3B4
JDM yow...
https://fbcdn-sphotos-c-a.akamaihd.n...d1270a91111a32
My new (used) un-manggled bonnet
https://scontent.xx.fbcdn.net/hphoto...26&oe=565D3F49
the illusive buble top
https://fbcdn-sphotos-h-a.akamaihd.n...36704a4953aab5
US Racing Kit
https://scontent.xx.fbcdn.net/hphoto...bf&oe=56627E36
well atleast they all here, and mostly are stored away now to my spare rooms until i finish the conversion.
now update with the K swap.
Heck it was hella lots of cut and re structuring the bay.
custom mounts etc... definately almost impossible... there is times that i was thinking what am i throwing my self into!
i've lost a few photos that i didn't get it backed up
but here is a few that i have again.. on FB ...
Left Wheel hub - inner shaft
https://scontent.xx.fbcdn.net/hphoto...24&oe=5664F69A
right wheel hub - inner shaft
https://fbcdn-sphotos-e-a.akamaihd.n...62adb278818520
left
https://scontent.xx.fbcdn.net/hphoto...af&oe=56658197
Right
https://fbcdn-sphotos-e-a.akamaihd.n...f737c6f89460a7
This is a much as i could get.
it sits as far up as possible - and yet to retain the straight shaft as you can see on above image drive shaft have to be almost inline
sits as far back as possible for the drive shaft to sit yet again alsmot inline
after speaking to a few drive shaft shop, i found the right guy to manufacture it.
we shall see how we go on this current mounting position.
once the drive shaft is done, Engine is again coming out to get fully serviced
Belts, injectors cleaned, broken sensor replaced etc.
then finalized the weld and tidying it up.
seal the weld and spray of new paint on the bay.
at the moment its all just 50-50 on temporary and fully welded.
lots of tidy up to do so, I'll keep you guys updated how i go with the shaft.
After ALLL THAT!
then i will start the wiring and lastly, shifter linkage hahahah! i hvnt actualy look into this yet but, yes is still do able may be in reverse mode
1 3 5
|-|-|-|
2 4 6 R
to
R 6 4 2
|-|-|-|
5 4 1
no 3rd gear
wat
two fourth gears, now this is my kind of machine
Loving the process you've taken and the progress you've made.
Keep the good shit going ########
You can buy a shifter cable and reversed linkage kit to suit a lotus it would work for you
Well, the car is still at the CV joint place.
Gave them a call last Monday, and they have not yet started on it.
Looks like its going to be a rather "Long" wait..
Getting out from the workshop for some fresh air..
Sorry currently its a little bit naked.. readers beware .. LOL
https://scontent.xx.fbcdn.net/hphoto...12386328_o.jpg
Up in the Towies flat bed and it looked dwarfed by it...
https://fbcdn-sphotos-e-a.akamaihd.n...59777288_o.jpg
https://scontent.xx.fbcdn.net/hphoto...78826236_o.jpg
Arrived at the CV joint place just in time before the down pour!
Woaah call that a lucky break ;)
https://scontent.xx.fbcdn.net/hphoto...f6&oe=56ABB13A
I'll leave it here for now.. until I get an update from the cv guys.
Oh ! regarding that Cable system, yes I did look into a few system and I think, i have some idea of how to make it works.
I've looked into Z car swaps, Mini Rear mounted K swap, MR-S K swap and Lotus
we'll see...
Love the updates! Good on you mate. Keep it uppp!
a bit slow lately due to other stuff
so just a short up date this time, I got the CV joints made by Alan's CV Joints
Cut and sleved joints and heat treated.
https://scontent.xx.fbcdn.net/hphoto...4c&oe=56F93A68
Almost impossible to make on one of them due the stubby short lenght, but we just got there..
They look pretty good, we shall see how they perform once its mounted.
one step closer
keen to see progress with the gb/linkages