Tucking the washer bottle in a DC2

Disclaimer: The following is provided as a GUIDE ONLY, and neither myself nor Ozhonda take any responsibility for the outcomes of someone else doing the following. You follow these steps at your own risk!


Aim: To Tuck the Winderscreen washer bottle in the gen 3 integra and make it looks more neat.

Required:
10mm socket and wrench
washer bottle from 98 spec jdm ITR
gromet ( which i got from the firewall of my other integra)


Step 1

First that off your front bumper,

refer to this if you dont know how to take it off
front bumper removal

Step 2

Locate the washer bottle on the passenger side of the car
and remove the old washer bottle out. And install the new washer bottle.

http://img111.imageshack.us/img111/44/dsc01238u.jpg

Step 3

98 spec vs 96 spec
Notice how the 98 spec hose is bendable, it can also be detached.
So once u fill it with water detach the hose.
http://img510.imageshack.us/img510/7874/dsc01239cfa.jpg

Step 4
Plug the hole on top of the washer bottle with the grommet from the fire
wall. Surprisingly it fits pretty well :p . It can also be used for the rear wiper
delete if you want to get rid of yours
http://img295.imageshack.us/img295/8656/dsc01240.jpg

And the finish product should look like this

http://img362.imageshack.us/img362/1537/dsc01242.jpg

C&C welcome :thumbsup:


I know the rest of my engine bay looks messy.. ill get to that next time ;)

How come no one commented on this? Looks pretty cool

:thumbsup:

so umm, couldnt we also just chop off that part where the piping meets the container, then put a plug over the top of that so it doesnt spill and use a funnel to fill the container? lol

but anyways, good job buddy

Good Work!!

might as well do a/c and p/s delete while you're at it XD
which grommet from the firewall did you use man?

lol..

i think might be the big grommet on the passenger side firewall next/below to battery

nice little trick, will that washer bottle fit up to an eg by any chance?

http://img362.imageshack.us/img362/1537/dsc01242.jpg

lol dont like your power steering pump? looks like youve owned the engine bay wall a couple times with the pulley

did you take out the B series to try and fit something else in? :P

u must have been bored duy.........lol

Thanks guys :thumbsup:

Quote:

---

Originally Posted by GIPONU

so umm, couldnt we also just chop off that part where the piping meets the container, then put a plug over the top of that so it doesnt spill and use a funnel to fill the container? lol

but anyways, good job buddy

---

U can but the hole might be too big, i had a spare jdm washer bottle so i did it lol.

Quote:

---

Originally Posted by MM89

might as well do a/c and p/s delete while you're at it XD
which grommet from the firewall did you use man?

---

Nah man, value my ac haha

Quote:

---

Originally Posted by m3ntAL_l2

lol..

i think might be the big grommet on the passenger side firewall next/below to battery

---

Yea its the one on the left of the battery

Quote:

---

Originally Posted by RandyRhydah

nice little trick, will that washer bottle fit up to an eg by any chance?

http://img362.imageshack.us/img362/1537/dsc01242.jpg

lol dont like your power steering pump? looks like youve owned the engine bay wall a couple times with the pulley

---

Not too sure if it will fit the eg's, the scratches were done by the noob old owner :(

Quote:

---

Originally Posted by MM89

did you take out the B series to try and fit something else in? :P

---

Yea.. putting in the d series.. lol

Quote:

---

Originally Posted by IEVAQ8

u must have been bored duy.........lol

---

i did it when i was installing Milans HID jdm headlights :thumbsup: 2 birds 1 stone lol

that's pretty cool :)