Search:

Type: Posts; User: ECU-MAN; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.21 seconds.

  1. Replies
    1
    Views
    3,454

    closed doubple post ...

    closed doubple post

    http://www.ozhonda.com/forum/showthread.php?191163-Axle-lenghts-for-K20-swap&p=4015009#post4015009
  2. Replies
    1
    Views
    2,224

    Check your VTS wiring from A4 of the ECU to the...

    Check your VTS wiring from A4 of the ECU to the solenoid, ensure you have continuity, make sure the Apexi is not wired into the VTS in any way
  3. The ground point on the thermostat housing is the...

    The ground point on the thermostat housing is the ECU's main ground point and its vital for correct operation, thus making the gearbox strap equally important.
  4. What codes do you get in the ECU

    What codes do you get in the ECU
  5. I would go with " My DIY b series loom swap is...

    I would go with "
    My DIY b series loom swap is cooked and i have zigged when i should of zagged" when the ECU detects a major issue it will trigger limp mode and register a fault code. Limp mode...
  6. Thread: Brake switch

    by ECU-MAN
    Replies
    3
    Views
    2,073

    probably cruse control

    probably cruse control
  7. Replies
    1
    Views
    2,631

    I can probably fix this for you depending on what...

    I can probably fix this for you depending on what the problem is, PM me.
  8. You do not have to have a passengers side...

    You do not have to have a passengers side inflator to have this issue, if you did have a passengers side inflator you would know, follow my instructions in post 26 regarding the dummy resistor as it...
  9. Replies
    10
    Views
    3,006

    yes .

    yes .
  10. Replies
    10
    Views
    3,006

    so why would you use it as sensor ground then ?

    so why would you use it as sensor ground then ?
  11. Replies
    10
    Views
    3,006

    I would seriously rethink grn/blk being ECT...

    I would seriously rethink grn/blk being ECT ground

    ensure grn/blk goes to sensor ground on the ECU

    if you try and drain the reverse lamps through grn/wht which is what I suspect is sensor...
  12. Replies
    10
    Views
    3,006

    What engine ? what year is the car ? what...

    What engine ?
    what year is the car ?
    what engine loom ?

    regardless

    Red/wht = ECT
    Grn/Blk = Revers Light Switch Pin1
  13. Replies
    116
    Views
    117,185

    DIY James di Griz please PM me your email address as...

    James di Griz please PM me your email address as I cannot reply to your PM since you are a guest
  14. Thread: 1994 Civic EG

    by ECU-MAN
    Replies
    1
    Views
    2,119

    Sounds like the VSS

    Sounds like the VSS
  15. Replies
    6
    Views
    2,554

    You need to make sure you use the correct...

    You need to make sure you use the correct thermistor as there are different types.
  16. Replies
    9
    Views
    3,160

    unplug the ECU

    unplug the ECU
  17. Replies
    18
    Views
    5,927

    3 things can cause this delay in your situation...

    3 things can cause this delay in your situation here

    1. as mentioned the ignition switch, but I doubt it

    2. the aftermarket immobiliser

    3. the factory immobiliser.


    Unfortunately your...
  18. Replies
    116
    Views
    117,185

    DIY Hi Jason I did receive your PM, did you get...

    Hi Jason

    I did receive your PM, did you get my reply ?
  19. Replies
    2
    Views
    2,751

    No delay relay, you switch off the ignition and...

    No delay relay, you switch off the ignition and power is lost to the ECU IG source immediately, that is why the ECU is wired with a VBU to keep constant 12v for memory.
  20. Replies
    8
    Views
    5,066

    sounds like the starter solenoid

    sounds like the starter solenoid
  21. Replies
    2
    Views
    2,339

    I can fix this ECU for you, PM me for more...

    I can fix this ECU for you, PM me for more details.
  22. Sounds like the gearbox main shaft bearing

    Sounds like the gearbox main shaft bearing
  23. Replies
    116
    Views
    117,185

    DIY User DonGak please PM me your email address as I...

    User DonGak please PM me your email address as I cannot reply to your PM
  24. Replies
    25
    Views
    7,165

    Any locksmith can clone the black key If you...

    Any locksmith can clone the black key

    If you get stuck message me, I can do it a lot,lot cheaper
  25. Replies
    25
    Views
    7,165

    You can clone the last black key with out the red...

    You can clone the last black key with out the red key

    You cannot add OEM black keys at a dealer with out the red key.

    It is possible to add red and black keys if all keys are lost however a...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4

» Recent Threads

Cars under the stars
Today 12:40 AM
Last post by matespace
Today 12:40 AM
0 Replies 31 Views
XPEL ULTIMATE PLUS &...
Yesterday 02:41 PM
Last post by CarCareProducts
Yesterday 02:41 PM
0 Replies 38 Views
Mostert rides the NZ...
18-09-2019 06:43 PM
Last post by matespace
18-09-2019 06:43 PM
0 Replies 52 Views
Top DIY brake repair tips
13-09-2019 09:53 PM
Last post by matespace
13-09-2019 09:53 PM
0 Replies 94 Views
Shock absorbers
04-09-2019 11:52 AM
Last post by mlracing
05-09-2019 09:58 AM
1 Replies 289 Views
DC5R Power Steering Pump
02-04-2013 09:26 PM
Last post by uccoffee
04-09-2019 11:55 AM
2 Replies 2,542 Views
Tickford Racing takes...
27-08-2019 11:28 PM
Last post by Vvvtec
31-08-2019 05:58 PM
1 Replies 348 Views
Bendix is Back at All...
23-08-2019 05:00 PM
Last post by matespace
23-08-2019 05:00 PM
0 Replies 291 Views

Powered by vBadvanced CMPS v4.1.3


Terms and Conditions
Ozhonda.com is in no way affiliated with the Honda motor company or Honda Australia in anyway whatsoever.