Search:

Type: Posts; User: ECU-MAN; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.03 seconds.

  1. Replies
    81
    Views
    240,159

    Sticky: this is not the SCS,its for the fog lights SCS...

    this is not the SCS,its for the fog lights SCS will be on the pasangers side near the ECU
  2. Replies
    81
    Views
    240,159

    Sticky: the main relay also powers the ECU, but the ECU...

    the main relay also powers the ECU, but the ECU first activates the relay, so If your relay is clicking then the realy or ECU could be at fault.
  3. Replies
    81
    Views
    240,159

    Sticky: no the engine will even start if there was...

    no

    the engine will even start if there was no compresson in that cylinder
  4. Replies
    81
    Views
    240,159

    Sticky: did the water level go above the boot level ?

    did the water level go above the boot level ?
  5. Replies
    81
    Views
    240,159

    Sticky: The Engine Lamp staying on is normal when the SCS...

    The Engine Lamp staying on is normal when the SCS is bridged,

    the flooding does not sound good. first change your spark plugs and see if she starts.

    does the fuel pump prime ?

    if you can...
  6. Replies
    81
    Views
    240,159

    Sticky: the blue 2pin is the SCS and the blue 3 pin is...

    the blue 2pin is the SCS and the blue 3 pin is the DLC, the 3 pin DLC should not be connected to anything.

    try shorting the 2 pin blue connector again.
  7. Replies
    81
    Views
    240,159

    Sticky: I would not go by what you heard as its wrong ...

    I would not go by what you heard as its wrong

    go by what you read in this thread, I suspect you have not bridged the correct 2 pin connector

    was it blue ? did it have a 3 pin connector next...
  8. Replies
    81
    Views
    240,159

    Sticky: MIL is not ment to blink with the LED for faults,...

    MIL is not ment to blink with the LED for faults,

    only go by the LED in the ECU for codes
  9. Replies
    81
    Views
    240,159

    Sticky: code 22 is excessive change in vehicle speed...

    code 22 is

    excessive change in vehicle speed sensor signal
    or
    a problem with average for vehicle speed and engine speed

    basicly if you have been reving the car higher than 2000rpm for...
  10. Replies
    81
    Views
    240,159

    Sticky: dead ECU dude, or poor wiring, but more dead...

    dead ECU dude,

    or poor wiring, but more dead ECU
  11. Replies
    81
    Views
    240,159

    Sticky: as above, check the TPS and O2 sensor, I dont...

    as above, check the TPS and O2 sensor,

    I dont remember code 71 from the OBD0 days
  12. Replies
    81
    Views
    240,159

    Sticky: yeah I know what you mean, Ill give it some...

    yeah I know what you mean, Ill give it some thought. and PM me if you have any good idea's
  13. Replies
    81
    Views
    240,159

    Sticky: you dont short the 2 pin plug on OBDO

    you dont short the 2 pin plug on OBDO
  14. Replies
    81
    Views
    240,159

    Sticky: fixed

    fixed
  15. Replies
    81
    Views
    240,159

    Sticky: 1, try another battery in your car. 2,...

    1, try another battery in your car.
    2, http://www.ozhonda.com/forum/showthread.php?t=68798
  16. Replies
    81
    Views
    240,159

    Sticky: cant you use the Hondata software to read the...

    cant you use the Hondata software to read the codes with your computer.

    being a Kpro system it could be a setting that is causing this
  17. Replies
    81
    Views
    240,159

    Sticky: modifying the ECU is not a simple procedure I...

    modifying the ECU is not a simple procedure I cant just explain to you, but you can try a 5w resistor on the VTEC wire from the ECU to ground, that also may fool the ECU
  18. Replies
    81
    Views
    240,159

    Sticky: the ECU looks for the resistance of the VTEC Sol,...

    the ECU looks for the resistance of the VTEC Sol, but since it goes to the emanage and not the VTEC sol there is no resistance so you get a code.

    I can modify you ecu not to look for the VTEC...
  19. Replies
    81
    Views
    240,159

    Sticky: is the emanage device taking control of VTEC...

    is the emanage device taking control of VTEC xover point
  20. Replies
    81
    Views
    240,159

    Sticky: can you explain your setup bit more, are you...

    can you explain your setup bit more, are you running a standard honda ecu with emanage piggy backed onto it. if so what is the emanage doing to the vtec solenoid. ig you have run a wire from the...
  21. Replies
    81
    Views
    240,159

    Sticky: EK1 is OBDII but it does not use the standard...

    EK1 is OBDII but it does not use the standard OBDIIa ot OBDIIb connectors.
  22. Replies
    81
    Views
    240,159

    Sticky: sometimes they are hard to see as they blend in...

    sometimes they are hard to see as they blend in with the wiring loom well.
  23. Replies
    81
    Views
    240,159

    Sticky: have a good look near the ecu area on the left...

    have a good look near the ecu area on the left kick pannel, it might be tucked in under there, you may have to remove the cover for a good look. look hard you will find it in a green rubber holser...
  24. Replies
    81
    Views
    240,159

    Sticky: try looking on the oppisite side where the ecu is.

    try looking on the oppisite side where the ecu is.
  25. Replies
    81
    Views
    240,159

    Sticky: code 19 coming soon !!!

    code 19 coming soon !!!
Results 1 to 25 of 30
Page 1 of 2 1 2

» Recent Threads

Finest Сasual Dating -...
05-03-2024 08:22 PM
by Monetz
Last post by Monetz
05-03-2024 08:22 PM
0 Replies 2,880 Views
Superlative Сasual...
29-02-2024 08:18 PM
by lommyvo
Last post by lommyvo
29-02-2024 08:18 PM
0 Replies 2,725 Views
Exemplary Сasual Dating...
29-02-2024 03:50 PM
by Muzzy
Last post by Muzzy
29-02-2024 03:50 PM
0 Replies 2,272 Views

Powered by vBadvanced CMPS v4.1.3


Terms and Conditions
Ozhonda.com is in no way affiliated with the Honda motor company or Honda Australia in anyway whatsoever.