Search:
Type: Posts; User: ROM30S ; Keyword(s):
Search :
Search took 0.01 seconds.
after closer inspection it is the clutch master cylinder.
the EM1 shares the same one with 5/8 marked on it.
Thanks for the reply, Im gonna probably replace both since one is attached to the other.
I found a replacement from an EM1 vtir, im just unsure at the moment if they are the same so im getting the...
recently I found a leak coming from the clutch pedal around the firewall entrance of the brake booster on my EK4.
would any on know from experience if this is the master cylininder or booster...
After multiple searches I couldn't find a clear answer.
I bought an EM1 exhaust myself so decided to share my knowledge on it.
The length of the piping and flange will bolt up directly onto the...
$1800 remove,recondition and install, Rob didnt even advise to do this he even said its too expensive.
Im gonna have to just look around for a second hand tranny or just buy another CRV ive seen...
thanks for the reply
I contacted Hannys Honda and they can rebuild the box for $1800 or if I find a box they can fit it for $350.
checked some wreckers, Hontoys asking $700 others were asking...
Hi all
I have a 98 CRV that recently started having issues with the auto transmission at higher speeds.
when it first occurred I found that there was not enough transmission fluid in it, it was...
Legend been searching everywhere for the EK4 blade offset
I guess something different, not realy any on the streets you see have been done its either stock or lowered with rims.
there cheap as to run, parts are easily to get and there fuel efficient
...
I ended up getting 205/70/16 offroad/road tyres as they didt have any bf goodrich instock.
the fronts fit perfect but the rear is very close, any fatter tyre and the bottom bit of the guard behind...
yeh thanks for the help man, nah you did well NOT
update
got my maye to come over as he has same car, i took out his ignition coil put into my car and boom.
cars running sweet.
went down to repco and bought one for $50
absolutley...
anyone know where I can buy the ignition switch or igniter?
brand new from honda ignition coil is $77 and ignition igniter is $160
or I can take the whole distributor to Hannys and theyl...
ok so far today took out all spark plugs n cleaned them, 1st n 2nd were covered in oil gave em a real good clean n sand then tried again
im now leaning towards it being an ignitir or coil problem ...
maeyby but the alarm and electrics are working fine, you think its worth replacing all the ground wires?
EK4 B16A completely stock except for injen cold air intake.
Today I filled up a full tank of fuel drove for about 15minutes, stopped at a set of traffic lights when the lights turned green I got...
Do you know if the stock height will fit the fatter tyres?
fuk yeh thats what im talking about, those are great shots man.
I hope to have my CRV similar
what tyres are you using tho all terain or just dirt tyres
hey guys has anyone lifted a CRV before as in raised it in like the below link
http://www.rocky-road.com/honda-crv-lift-kit.html
Im interested to do the same but unsure where to shop in Sydney...
Bought the jap import and sold it ages ago hahah now Ive got an aussie delivered rd1
the jap one pretty much had different interior, 4 stud instead of 5 stud hub and a different rear bar n boot
...
Nice setup Ive always wanted to boost the d16.
How reliable has it been, do you drive it daily?
Does anyone know if the stock hatch muffler will fit straight on if the cars fitted with a whiteline rear swaybar which also has the back plate?
has anyone fitted the ebay style D16y4 headers onto a ZC crx motor before?
I kno D series headers should all line but up has anyone actualy fitted these extractors onto a CRX before and can shed...
went to eastern creek drag way last night ran a 16.1 down the quarter mile.
does any one know if that's any good for a d16y4? been doing some research but can only find times for d16y7
200K service getting done today.