Results 1 to 1 of 1
  1. #1
    Member Array
    Join Date
    Dec 2014
    Location
    Perth
    Car:
    1995 EG Ciivic

    IDLE Issues SURGES, etc - IACV Cleaning - Understanding

    (I posted this earlier as an extension of a previous question I asked - then solved, however this may be easier for others)

    Despite common perceptions the Honda IACV component is not one that regular fails - becomes dirty yes, fails no; this is primarily due to the simplistic design.

    Basically the IACV contains a small electro Magnetic Valve that Slides back and forth - opening and closing to allow the flow of coolant based on engine demands. this Valve can become blocked - consider it similar to the build up of calcium in a shower head. the build up of sludge sticks to both the inner chamber and the slider. over time the slide cannot close.

    The surging thus caused is usually a process of this; (DONT Quote me - there is a chance I wrote it backwards - but the process is accurate)

    Engine heats up, slider Valve activates. Slider however cannot close/open properly due to sludge/blockage - this failure causes the engine to surge, when the engine revs move beyond a certain point the slider attempts to activate again, closing/opening the flow enough to cause a drop in revs but an inability to complete the process hampers this and it becomes circular. the car is continually trying to close/open to finish the process. each failure requires another adjustment elsewhere involving air, fuel etc.

    To solve this you need to remove the throttle body as shown here

    http://www.ozhonda.com/forum/showthr...ting-Look-here

    1. you then need to remove the IACV from the throttle body.

    if you look closer you can see the "tongue" of the valve slider section. that needs to glisten. with my IACV I removed the electromagnetic component - be AWARE there is a glued seal underneath, it WILL become a little damaged however this is predominantly related to keeping moisture out - I havent researched if it can be bought - however there are types of glues that are able to make those sort of tiny "gaskets".

    1b. removing the Electromagnetic component allows you to slide it back and forth - with my IACV it would NOT move, it had that much sludge.

    2. you need to clean the IACV chambers and slider with Carb Cleaner, perhaps a toothbrush and tiny cotton buds.

    3. when it shines, then reassemble. (I am NOT certain about the distance the slider tongue needs to be before the controller side is added again - i took a photo and ensured it was the same gap. there is a chance that the controller side has a specific range.) The magnet will SNAP back in place when the controller is added.

    4. reassemble the Throttle Body etc, put your car back together.

    My car run smooth as new.

    For extra info, look here. Explains the Electro/mechanics

    http://www.fuelly.com/forums/f10/mor...iacv-7495.html
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	NfvCkQf.jpg 
Views:	4 
Size:	126.9 KB 
ID:	30277   Click image for larger version. 

Name:	eb8ITwT.jpg 
Views:	5 
Size:	184.6 KB 
ID:	30278   Click image for larger version. 

Name:	95RWuSV.jpg 
Views:	4 
Size:	96.7 KB 
ID:	30279   Click image for larger version. 

Name:	SZC2NEX.jpg 
Views:	4 
Size:	154.2 KB 
ID:	30280  

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Powered by vBadvanced CMPS v4.1.3


Terms and Conditions
Ozhonda.com is in no way affiliated with the Honda motor company or Honda Australia in anyway whatsoever.