EP3 Type R

[Lukezen27]

just wanted to ask guys if this is the correct O2 sensor for the EP3? http://www.amazon.com/dp/B000C5WCLS/...0_pd_re_dt_dt2
Would it be recommended to replace the secondary O2 sensor at the same time?

Na secondary doesn't seem to brake much

[TonyxTony]

White lithium grease is what is used to grease it up just make sire u get it right in there and turn your wheels side to side and apply allround then use a zip tie or a hose clamp to seal it all up again.

Thanks i will give it a go this week.

It seens abit far in. is there an easier way to get to it?

also on the right side. do I need to take off the intake?

[UNA91]

Lol I just worked with the motor in the way, just get some pliers and maybe wire cutters and pry that metal clip off, then use zip ties or a large hose clamp to close it. For the right side you do have to take the intake off, but if you have a CAI then probs not

[brody]

Hey guys,
Anyone know the part numbers for primary and secondary o2 sensors for our ep?

[RPS.13]

Hey guys,
Anyone know the part numbers for primary and secondary o2 sensors for our ep?

Primary o2 sensor OEM part number: 36531-PRB-A01 (number on the box, purchased from JDMYard)

Secondary o2 OEM part number (printed on the actual unit): NTK OHJ:562-H7 (Which proved to be quite difficult to find a OEM replacement)

I ended up getting an aftermarket Denso 234-4122 Oxygen Sensor, more info here http://www.ozhonda.com/forum/showthr...=1#post3301180 Post #12437

The secondary sensor, I wouldn't bother with changing it unless your actually getting a CEL specifically stating that it has malfunctioned or a similar error code.

[UNA91]

Man, just took the ep3 for a spin tonight after 2 weeks sitting in the garage, and my gosh i love my car haha feels good to hit vtec again.

[Icebox]

Well I'm using the mugen engine mounts and I find that they are pretty good. You can order them from rhd japan for about $300.

how much was shipping from Rhd japan? i was thinking of getting the j's racing one plus some other small stuff but it didnt say anything about shipping so it stopped me

[bluey45]

how much was shipping from Rhd japan? i was thinking of getting the j's racing one plus some other small stuff but it didnt say anything about shipping so it stopped me

When I ordered my mugen mounts from RHD they cost me $330 all up. Shipping was about $40. Ended up still cheaper than buying in oz.
You may need to register a account and when you put items in your trolley it should give you the postage cost.

[butterfingers]

does anyone get surprise mods? some importers have no idea seriously.

cleaning the engine bay last night and found an engine torque damper, js racing tie rod, j's racing lower tie bar, some blue colored aftermarket rear camber arms that was not listed on the mods list when i bought it. how delightful.

[bluey45]

does anyone get surprise mods? some importers have no idea seriously.

cleaning the engine bay last night and found an engine torque damper, js racing tie rod, j's racing lower tie bar, some blue colored aftermarket rear camber arms that was not listed on the mods list when i bought it. how delightful.

Serious? That's pretty sweet.

[Icebox]

When I ordered my mugen mounts from RHD they cost me $330 all up. Shipping was about $40. Ended up still cheaper than buying in oz.
You may need to register a account and when you put items in your trolley it should give you the postage cost.

thats some pretty cheap! might jump on it before our dollar gets worst, haha

does anyone get surprise mods? some importers have no idea seriously.

cleaning the engine bay last night and found an engine torque damper, js racing tie rod, j's racing lower tie bar, some blue colored aftermarket rear camber arms that was not listed on the mods list when i bought it. how delightful.

I did, i thought i was running on a cheap aftermarket exhaust system,

but what i found was a spoon axle back n1 exhaust, unknown mid pipe + a high flow cat.

plus a couple yens in the cabin

[brody]

Primary o2 sensor OEM part number: 36531-PRB-A01 (number on the box, purchased from JDMYard)

Secondary o2 OEM part number (printed on the actual unit): NTK OHJ:562-H7 (Which proved to be quite difficult to find a OEM replacement)

I ended up getting an aftermarket Denso 234-4122 Oxygen Sensor, more info here http://www.ozhonda.com/forum/showthr...=1#post3301180 Post #12437

The secondary sensor, I wouldn't bother with changing it unless your actually getting a CEL specifically stating that it has malfunctioned or a similar error code.

Awesome thanks for that. Yeh.. my primary is screwed so ill just replace that one.
No problems with the Denso?