[How To]Hardwiring a Dashcam into the Civic Hatch(2006-2011)

[Grayfox]

This is a how to on how to hardwire a dashcam if a basic dashcam that does not have a hardwire kit as an option into the 8th gen civic hatchback


Things you will need:
The dashcam
http://i662.photobucket.com/albums/uu346/IgrayfoxI/Civinfo%20How%20Tos/Dashcam%20Install/20131113_190108.jpg

Female Microspade Connector
http://i662.photobucket.com/albums/uu346/IgrayfoxI/Civinfo%20How%20Tos/Dashcam%20Install/20131113_190115.jpg

Small Fork Connectors
http://i662.photobucket.com/albums/uu346/IgrayfoxI/Civinfo%20How%20Tos/Dashcam%20Install/20131113_190126.jpg

Heatshrink tube
http://i662.photobucket.com/albums/uu346/IgrayfoxI/Civinfo%20How%20Tos/Dashcam%20Install/20131113_190136.jpg

Basic cutters
http://i662.photobucket.com/albums/uu346/IgrayfoxI/Civinfo%20How%20Tos/Dashcam%20Install/20131113_190148.jpg

12v to 5v buck converter
http://i662.photobucket.com/albums/uu346/IgrayfoxI/Civinfo%20How%20Tos/Dashcam%20Install/20131113_190159.jpg

Crimping tool
http://i662.photobucket.com/albums/uu346/IgrayfoxI/Civinfo%20How%20Tos/Dashcam%20Install/20131113_190208.jpg

Wire(if needed)
http://i662.photobucket.com/albums/uu346/IgrayfoxI/Civinfo%20How%20Tos/Dashcam%20Install/20131113_190218.jpg

Phillips Screw Driver
http://i662.photobucket.com/albums/uu346/IgrayfoxI/Civinfo%20How%20Tos/Dashcam%20Install/20131113_192135.jpg

Pry tool
http://i.ebayimg.com/00/s/NzAxWDcwMQ==/z/-EsAAOxyOa9RyVaR/$(KGrHqZ,!roFG6ktTf7hBRyV,RpPIg~~60_12.JPG

1: Cut enough wire 1.5m should be more than enough
http://i662.photobucket.com/albums/uu346/IgrayfoxI/Civinfo%20How%20Tos/Dashcam%20Install/20131113_190441.jpg

2: install the mini spade connector to the end of wire and cover the end with some heatshink tubing
http://i662.photobucket.com/albums/uu346/IgrayfoxI/Civinfo%20How%20Tos/Dashcam%20Install/20131113_191117.jpg
http://i662.photobucket.com/albums/uu346/IgrayfoxI/Civinfo%20How%20Tos/Dashcam%20Install/20131113_191557.jpg

3 Strip the ends of the buck converter
http://i662.photobucket.com/albums/uu346/IgrayfoxI/Civinfo%20How%20Tos/Dashcam%20Install/20131113_191828.jpg

4: Open the drivers door and using the pry tool remove the panel pictured
http://i662.photobucket.com/albums/uu346/IgrayfoxI/Civinfo%20How%20Tos/Dashcam%20Install/20131113_192402.jpg

5: Remove the screw that is holding the lower dash panel and pull down to lower the panel
http://i662.photobucket.com/albums/uu346/IgrayfoxI/Civinfo%20How%20Tos/Dashcam%20Install/20131113_192340.jpg

6: Undo the upper or lower screw and install the ground wire and tighten the screw
http://i662.photobucket.com/albums/uu346/IgrayfoxI/Civinfo%20How%20Tos/Dashcam%20Install/20131113_192742.jpg

7: Insert the wire between the dash and the Lower A Pillar
http://i662.photobucket.com/albums/uu346/IgrayfoxI/Civinfo%20How%20Tos/Dashcam%20Install/20131113_192811.jpg

8: Insert the wire inside the driver side of the A Pillar
http://i662.photobucket.com/albums/uu346/IgrayfoxI/Civinfo%20How%20Tos/Dashcam%20Install/20131113_192947.jpg

9: Connect the buck connector the the dashcam and insert the rest into the roof leaving the ends out
http://i662.photobucket.com/albums/uu346/IgrayfoxI/Civinfo%20How%20Tos/Dashcam%20Install/20131113_193339.jpg

10: Connect both wires together and put heatshrink over it
http://i662.photobucket.com/albums/uu346/IgrayfoxI/Civinfo%20How%20Tos/Dashcam%20Install/20131113_193917.jpg
http://i662.photobucket.com/albums/uu346/IgrayfoxI/Civinfo%20How%20Tos/Dashcam%20Install/20131113_195054.jpg

11: Connect the power feed line to the option connector
Connect the bottom right connector for ignition or bottom left for constant battery power if you want to use the dash cams motion sensor(note you will need a fuse in slot 27)(note this may drain your battery)
http://i662.photobucket.com/albums/uu346/IgrayfoxI/Civinfo%20How%20Tos/Dashcam%20Install/20131113_234205.jpg

12: Tuck the the rest of the wires in the roof and test
http://i662.photobucket.com/albums/uu346/IgrayfoxI/Civinfo%20How%20Tos/Dashcam%20Install/20131113_234046.jpg

If your dash cam does not need +5v power you can just you wire and a DC jack to connect to it.

[lolmclol]

nice write up!

what are the specifications of the camera?

[sensei_]

looks like a uniden iGo 300.

[lolmclol]

looks like a uniden iGo 300.

http://static2.ozhonda.com/forum/images/reputation/reputation_highpos.png

[Grayfox]

The camera is a Uniden iGo CAM 300.

It can record at 1920x1080, has motion sensing and it is small, it does NOT have a GPS but it is a good basic camera.
You can get some blocking on the road and the upper dash in low light.
The Infra red LEDs are useless and they do not light up anything that is more than 1m in front(they are low powered ones)

This guide applys to any dashcam really.

As for the civic sedan, i do not know what it's internal fusebox looks like or even if it has the option connector on it, but you can tap another ignition powered source.

[Grayfox]

This is a guide on the pinouts on the 8th gen civic hatch option connector
It can be used for reverse cameras, dash cams, and DRLs.
http://imageshack.us/a/img197/9395/77jd.png

This guide can be also applied to the new 8.5gen civic, note you do NOT NEED A FUSE anymore, FUSE 27 controls something else as per Bog from civinfo (http://www.civinfo.com/forum/1669909-post49.html), the option connector is located on MICU1
http://imageshack.us/a/img834/3907/oclf.png

[EKVTIR-T]

that cam on special at bigw $48

http://www.bigw.com.au/offer/catalogue#view=product&itemId=5966104&saleId=5966