Search:
Type: Posts; User: rk 86 wa ; Keyword(s):
Search :
Search took 0.02 seconds.
Hey buddy, thanks for the reply. It's not that engine mount however. I've popped and replaced that same mount a whole ago and the rattling is completely different. There are no extreme vibrations....
Hi folks,
Got a bit of a rattle that has appeared in my vti.
Turning or driving at low speeds (0-20km/h) in 1st/2nd (yet to try 3rd) will generally result in a rotational rattling sound. ...
Pay the extra couple hundred and get something better for sure.
Had my experiences, bought them as a first set of coilovers and was blown away at what they offered until they started breaking...
...
not trying to be rude, but has your gf/wife/someone else (or possibly yourself) driven the car, riding the clutch everywhere?
My sister took my car out to do some 'l's driving with my dad and what...
Thanks guys :) will have a look see after work
I have problems with my blades in that they hop over the glass, rather than wipe it.
This results in half the glass being 'missed' and a shitty loud noise every time they wipe.
Its my second...
You can buy fd1 pads from endless, ferodo, ebc AFAIK
Do a google search and grab the part number, send it off to your local parts shop and win.
Pull off the wheel and check the positions of the sleeves i.e if there is a space between them which may cause slapping.
Alternately look in the engine bay and see if the top nut that holds the...
hey guys, ive blown a mount and need a replacement.
I was wondering if anyone knew of aftermarket replacements for the r18 or if one from a k series fits?
thanks a lot
ryan
All this thread does is make Doma look like a **** hahaha.
If you didnt come across like a ****wit with your fn2r defending then maybe people would take some of your posts seriously.
Reading...
heh nice photos bede :)
Busso is one of those stages too scary to push at in my daily driver hahaha.
Bring on Jacks Hill then Albany :)
Tim, possible that if they did anywork on the hub or wheel bearing that they flipped it and pushed it in back to front. The Abs sensor on our cars is on one side of the wheel bearing which reads off...
WTF?!!!
What was damaged and didnt they just write your car off?
Depends on how low the revs are dropping, go to honda ask them to have a suss of your idle solenoid.
Had similar problems with mine :)
Car Model:fd
Front Wheel and Tyre Size: 17 X 7 +42 215/40R17 toyo tasw
Rear Wheel and Tyre Size: 17 X 7 +42 215/40R17 toyo tasw
Suspension: stock
Guard Modifications:n/a
Issues with Setup: n/a
...
If you are doing light track work then go the ku36 as long as its not circuit based and you dont hammer your tyres with consistant high heat cycles. I.e hill climbs/ sprints/ motorkhanas etc.
If...
should be 5 x 114.
They should fit but the offset will be terrible (I know cause I use accord rims as dailys haha and they are +55 IIRC)
Ive killed a wheel bearing by the suspected use of 15mm kics bolt on spacers on my fd1.
That 15mm although it may seem negligant, does result in a larger moment about the bearing and hence loads...
It definately wasnt a nasty hole in my fuel map lol.
Thanks for the advice Monty, just loosened the two bolts holding the top of the knuckle to the bottom of the coilover and held the coilover and...
Hi guys,
Bearing in the civic was changed on the weekend and after chucking the car back together the camber on the front passenger has dropped from a ~-2.2 to what seems like a ~1, enough of a...
Uwa ftw ;)
Also nice work, good luck for 2010 season!
+1 thanks a lot. will make diy rotor change easier :P
Putting spacers on the front of your car allows for wider track width as mentioned before.
Your car will "understeer" or "oversteer" when you overload the tires load as they are what is...
Get bolt on spacers at your own peril, I just killed a wheel bearing and a contributing factor was the 15mm spacer I was using.
» Recent Threads
Wobbling Brakes
26-04-2024 12:20 PM
26-04-2024 12:20 PM
0 Replies 384 Views