Search:

Hey guys, my DC2 b18c2 has developed a weird pulsing idle.

The problem happens randomly, sometimes doesnt happen sometimes its constant.
The revs sit at 1500 and it's like the pedal is...

Pulled injectors out today, they were dirty as shit.

Cleaned up, replaced fuel filter too and missfiring has gone completely, drove for about 30mins with no problems.

Did find a small crack on...

You were spot on about the vac lines. Found the vac line that controls the butterfly in intake broken....

Update: Now on WOT the engine sounds completely different almost like a subaru but no lack in power.

Should I be worried?

Replaced ignition coil, leads, dizzy cap and problem fixed.

Not sure why o2 sensor would cause 1 cylinder to miss fire?

Okay, so replaced the rotor and coil and still missfires at low revs.
Compression was good 210 all round.
Cylinder 4 spark plug was fouled (other 3 looked normal)

Anymore suggestions?

Dc2 Vtir 1994 sputtering on low revs, sounds like its miss firing.

Am I right to say the ICM and distributor cap are the problem?
Where's the best place to buy these? Honda?

Thanks.

Looking to get new shocks and springs for Dc2 vtir.
Only street driving but I'd like something stiffer than stock and budget 600-1000.

Koni shocks with GC springs seem to be pretty popular, I'm...

How bad is this damage?

Can I sand and polish or do I need a repaint?

http://imageshack.com/a/img835/6499/qsbve.jpg

http://imageshack.com/a/img844/3379/u6gu.jpg

I'm fairly sure the leak is at the clutch pedal. This would be the clutch master right?

Are there rebuild kits available or would I have to buy a new master.

Dc2 vtir, every 2-3 weeks my clutch fluid level drops by like 5mm, atm I am just topping it up and monitoring. I can't find any visible leaks in the engine bay, anyone no what the problem could be?
...

Where would I find a replacement vtec solenoid (solenoid and housing)

Any further suggestions? I've been searching and some people say its the sock that goes on the bottom of the fuel pump.

http://honda-tech.com/showthread.php?t=3024291

Nah. It's a daily barely ever get past 3.5k revs

Using Vortex 98 and get around 300 before I fill up again (when gauge is around 1/3 left)

Car: dc2 vtir 93'

When the fuel gauge gets to about 1/4 I can hear a buzzing sound while driving (sounds like an electric motor or something), when I take sharp corners or go around a roundabout...

I am planning to get new shocks and springs for my DC2 vtir.

Been looking at Koni STR.T shocks with either skunk2 lowering springs or Eibach sportline lowering springs.

The specs say that they...

Hi, I recently picked up a type R full cat back exhaust + type R cat for free off a mate. Will this fit my stock vtir header and B pipe?

Also, when driving for a long time the handbrake console,...

Yes still wearing it in, read a guide beforehand. I've only done like 30km's around suburbs.
And used the old flywheel.

I don't see how I could have bump the TPS, seeing as it is attached quite...

OK, so recently my clutch died so I replaced the clutch at home(it was a massive job)

Put everything back together and now the engine seems kind of sluggish.

For instance it does not seem to be...

Due to me only signing up recently, I cannot post in the for sale forum.

My dc2 vtir teg has engine issues and I'm currently looking for a B18cr +box to replace it with.
Anyone selling ?
Budget...

Any tool to tell if they are stretched? I think I'll just get a set of new ones. Know where I can get them?

And will them valves need grinding with grinding compound?

So, I have a jdm b18cr, have skunk2 stage 2 cams, valves and retainers.

My question is, since I am doing the valves (head must be removed) should I just get a new set of head bolts? or is it safe...